ProMaster Wireless Remote Shutter Release - Olympus w/UC1 Connector
$ 89.95 $ 49.95
ProMaster Wireless Remote Shutter Release - Olympus w/UC1 Connector
ProMaster SKU: 1831 | Helix SKU: PR1831
Overview
328'/100m working distance Compatible with all shutter release functions.
ProMaster Wrinkle Resistant Backdrop - 10'x20' - Chroma Key Green
$ 109.95
ProMaster Wrinkle Resistant Backdrop - 10'x20' - Chroma Key Green
ProMaster SKU: 3009 | Helix SKU: PR3009
Overview
ProMaster Wrinkle Resistant Backdrops give a smooth, clean looking background to your photos. Any wrinkles from storage or transport come out with low heat or steam while the background is hanging. They can be machine washed with mild detergent and tumble dried on low. The sewn-in rod pocket makes it easy to hang.
ProMaster Wrist Strap
$ 9.95
ProMaster Wrist Strap
ProMaster SKU: 7723 | Helix SKU: PR7723
Overview
- Light weight woven design
- Quick release clip makes it easy to attach and remove
Specifications
ProMaster XC-M 522 Column Tilt Adapter
$ 29.95
ProMaster XC-M 522 Column Tilt Adapter
ProMaster SKU: 4021 | Helix SKU: PR40215
Overview
The PROMASTER 4021 Column Tilt Adapter expands the capability of your XC-M 522 aluminum or XC-M 522C carbon fiber tripod by giving its center column the freedom to tilt 180° (90° up & 90° down). This adapter essentially converts your XC-M's center column into a multi-position, adjustable boom.
Just unscrew the weight hook from the center column, loosen the center column twist lock and slide it out of the tripod. Replace it with the 4021 Column Tilt Adapter, tighten the twist lock, and open the flip lock on the Column Tilt Adapter. Insert the center column and close the flip lock. This conversion can easily be done in less than 30 seconds. That's all there is too it!
Once your XC-M 522 has been converted you can reinstall the weight hook to the bottom of the adapter and add weight for more stability. A second, retractable weight hook is included with this adapter which you can use at the end of the boom (end of the center column) to counterweight your camera.
To operate the boom, loosen the main knob on the 4021 Adapter while holding your camera and then tilt the assembly into whatever position you like before tightening the knob. To rotate the boom, loosen the twist lock on the yoke of the tripod and spin the adapter. To extend or retract the boom use the twist lock on the column to adjust its upper stage.
This adapter has a number of teeth machined within its joint to give it an excellent amount of holding power in various tilt positions. Be sure to tighten its main knob before you release your camera to prevent it from falling.
The 4021 Column Tilt Adapter can be installed and used permanently on your XC-M 522, if you so choose, because it can achieve the same vertical position as the 'normal' center column when needed.
Truth be told, this is a wicked-cool accessory. It's great for macro work, extending your camera over a tabletop or a flowing creek. And it makes other tripods highly jealous.
Specifications
- Dimensions: 5 3/8" / 137 mm long. 22mm tube diameter.
- Weight: 4 3/8 oz / 124 g
* Dimensions and weight are for the adapter sans the weight hook
ProMaster XC-M 522 Extension & Macro Legs - Aluminum
$ 24.95
ProMaster XC-M 522 Extension & Macro Legs - Aluminum
ProMaster SKU: 3545 | Helix SKU: PR35457
Overview
The PROMASTER 3545 Aluminum Extension & Macro Legs work with XC-M 522 tripods. After removing all 3 of the XC-M 522's legs these extensions attach in their place. Now you have a choice. Either reattach the legs to these extensions and you get a very stable tripod with 6" more height, OR attach the 3 soft feet (included) to the extensions thereby converting your tripod into a lightweight, super-strong macro tripod.
The 3545 Extension & Macro Leg set adds amazing versatility to your XC-M 522 tripod.
Specifications
- Adds 6" / 152 mm of length to each XC-M 522 leg section
- Actual dimensions of each leg extension: 6 3/8" / 162 mm long x 22mm diameter
- Weight of each leg extension: 1 7/16 oz / 41 grams
- Weight of each foot: 3/8 oz / 11 grams
ProMaster XC-M 522 Ground Level Adapter - Aluminum
$ 12.95
ProMaster XC-M 522 Ground Level Adapter - Aluminum
ProMaster SKU: 3517 | Helix SKU: PR35174
Overview
The ProMaster 3517 Ground Level Adapter is a great accessory for getting an XC-M 522 tripod lower and closer to the ground for macro photography and a unique perspective.
Start by extending the upper stage of your XC-M's 2-stage center column. Unscrew the upper portion of the column (including the head) from the rest of the column. Now remove the weight hook and slide the lower part of the column completely out of the tripod. Replace it with the 3517 ground level adapter and insert the upper stage of the column into the 3517 adapter. Voila! In less than 30 seconds you have converted your XC-M 522 into a lowerider! You can now achieve a stable position as low as just 6" / 15.25 cm.
The Ground Level Adapter can also accept the XC-M's weight hook Just screw it into the bottom of the adapter and use it to add additional weight and stability to your XC-M 522.
FEATURES:
- Works with ProMaster XC-M 522 aluminum and XC-M 522 carbon fiber tripods
- Compatible with the XC-M 522 retractable weight hook
- Fast and easy to use
- Achieves a minimum working height of just 6" / 15.25 cm
Overview
- Dimensions: 3" / 76 mm long | 22 mm diameter tube
- Weight: 1 7/16 oz / 41 g
ProMaster XC-M 522 Ground Level Adapter - Carbon Fiber
$ 16.95
ProMaster XC-M 522 Ground Level Adapter - Carbon Fiber
ProMaster SKU: 3524 | Helix SKU: PR35242
Overview
The ProMaster 3524 Ground Level Adapter is a great accessory for getting an XC-M 522 tripod lower and closer to the ground for macro photography and a unique perspective.
Start by extending the upper stage of your XC-M's 2-stage center column. Unscrew the upper portion of the column (including the head) from the rest of the column. Now remove the weight hook and slide the lower part of the column completely out of the tripod. Replace it with the 3524 ground level adapter and insert the upper stage of the column into the 3524 adapter. Voila! In less than 30 seconds you have converted your XC-M 522 into a lowerider! You can now achieve a stable position as low as just 6" / 15.25 cm.
The Ground Level Adapter can also accept the XC-M's weight hook Just screw it into the bottom of the adapter and use it to add additional weight and stability to your XC-M 522.
FEATURES:
- Works with ProMaster XC-M 522 aluminum and XC-M 522 carbon fiber tripods
- Compatible with the XC-M 522 retractable weight hook
- Fast and easy to use
- Achieves a minimum working height of just 6" / 15.25 cm
Specifications
- Dimensions: 3" / 76 mm long | 22 mm diameter tube
- Weight: 1 3/16 oz / 34 g
ProMaster XC-M 522 Leg Warmers 3pc set - Black
$ 14.95
ProMaster XC-M 522 Leg Warmers 3pc set - Black
ProMaster SKU: 3594 | Helix SKU: PR35945
Overview
ProMaster's 3594 Leg Warmers are specifically designed for use with ProMaster XC-M 522 and XC-M 522C tripods. This kit of 3 warmers fits the 3 XC-M522 tripod legs perfectly. Simply wrap a leg warmer around the upper leg section of the tripod and zip it up. Now the leg is protected from scratches while covered in a soft sleeve. The warmers are much easier on your hands in cold weather too since they protect your skin from having direct contact with cold metal. And when you convert your XC-M tripod into its monopod mode, the warmer continues to perform as a soft, warm spot to hold on to.
Installing the leg warmers takes a bit of time and concentration since you have to line up the zipper while pulling the warmer tight around the leg. Be patient! Since it is an exact fitting item there is no slack in the fabric to ensure excellent performance once installed.
Specifications
- Actual length of each leg warmer: 5 1/8" / 130 mm
- Actual weight of each leg warmer: 13/32 oz / 11.5 g
ProMaster XC-M 522 Replacement Rubber Feet (set of 3)
$ 7.95
ProMaster XC-M 522 Replacement Rubber Feet (set of 3)
ProMaster SKU: 3503 | Helix SKU: PR35037
Overview
3503 is a replacement set of 3 standard feet for any XC-M 522 aluminum orcarbon fiber tripod. These are a great, inexpensive replacement set if you happen to lose or damage the standard feet on an XC-M 522 tripod.
The XC-M 522 standard feet are normally installed on the tripod from the factory. They are designed to be removable, thereby exposing a 3/8"-16 threaded port on the bottom of each XC-M 522 leg. The threaded ports can be used for connecting other accessories, like the popular All Terrain Feet (ProMaster product code 3510). If you need to replace any, or all 3 of the standard feet on a ProMaster XC-M 522 tripod this set is your solution.
* Please note, these feet do not work with the XC-M525 series tripods. If you need XC-M525 standard, replacement feet please refer to ProMaster product code 3720.
Specifications
Weight: 5/32 oz / 4.5 grams
ProMaster XC-M 522 Replacement Weight Hook
$ 5.95
ProMaster XC-M 522 Replacement Weight Hook
ProMaster SKU: 3706 | Helix SKU: PR37062
Overview
The 3706 is a replacement, retractable weight hook for any XC-M 522 aluminum or carbon fiber tripod. It connects to the bottom of the center column and allows you to attach additional weight to the tripod to improve its stability.
The 3706 is also a replacement hook for the 4021 XC-M 522 Tilting Column Adapter. With the Tilting Column Adapter installed you can add weight to the bottom of the adapter as well as to the bottom of the column. This improves the overall stability of the XC-M522 tripod while also counterbalancing your camera rig.
Finally, the 3706 also works with the 3517 XC-M 522 aluminum ground level adapter and the 3524 XC-M 522 carbon fiber ground level adapter.
Specifications
Weight: 9/32 oz / 8 grams
ProMaster XC-M 522C Extension & Macro Legs - Carbon Fiber
$ 34.95
ProMaster XC-M 522C Extension & Macro Legs - Carbon Fiber
ProMaster SKU: 3552 | Helix SKU: PR35525
Overview
The PROMASTER 3552 Carbon Fiber Extension & Macro Legs work with XC-M 522C tripods. After removing all 3 of the XC-M 522C's legs these extensions attach in their place. Now you have a choice. Either reattach the legs to these extensions and you get a very stable tripod with 6" more height, OR attach the 3 soft feet (included) to the extensions thereby converting your tripod into a lightweight, super-strong macro tripod.
The 3552 Extension & Macro Leg set adds amazing versatility to your XC-M 522C tripod.
Specifications
- Adds 6" / 152 mm of length to each XC-M 522C leg section
- Actual dimensions of each leg extension: 6 3/8" / 162 mm long x 22mm diameter
- Weight of each leg extension: 1 1/32 oz / 29 grams
- Weight of each foot: 3/8 oz / 11 grams
ProMaster XC-M 522K Professional Tripod Kit with Head - Black
$ 159.95
ProMaster XC-M 522K Professional Tripod Kit with Head - Black
ProMaster SKU: 3405 | Helix SKU: PR34054
Overview
The PROMASTER XC-M 522 tripod's 5-section, transverse legs fold 180° making the entire unit just over 12" long for storage and travel. Yet, fully extended it reaches a comfortable working height. Each leg's angle and length are independently adjustable, allowing the XC-M 522 to properly support your camera on uneven ground. Its dual-action ball head is strong, precise, and lightweight with an independent pan control. It has an integrated memory lock for repeatable tension control and uses ProMaster's dovetail quick release system for a fast camera connection.
The XC-M 522 is more than just a tripod, it's part of an expansive modular system.
FEATURES:
- Built-in monopod
- Transverse 180° folding legs
- Dual-action ball head with tension memory lock
- Independently adjustable leg angles
- 2-Stage, reversible center column
- Bubble levels on tripod and ball head
- Retractable weight hook
- ProMaster dovetail Q/R system (arca-swiss compatible)
- Soft, comfortable grips on touch points
- Modular design is expandable & customizable
Specifications
KIT SPECIFICATIONS
-
Maximum Working Height: 53 1/8" / 135 cm
-
Maximum Height with Column Down: 41 3/8" / 105 cm
-
Minimum Working Height: 12 1/2" / 31.8 cm *Minimum working height can be improved to 6" / 15.25 cm by adding a 3517 XC-M 522 Ground Level Adapter (sold separately)
-
Folded Length: 12 3/16" / 31 cm
-
Maximum Load: 11 lbs / 5 kg
-
Weight: 2 lbs 8 1/2 oz / 1.15 kg
-
Cold Weather Performance: -4° F / -20° C
- 5-Section Aluminum Legs
* Kit specifications include tripod with head attached
BALL HEAD SPECIFICATIONS
-
Height: 3 1/4" / 8.3 cm
-
Base Diameter: 1 5/8" / 4.1 cm
-
Weight: 8 oz / 226 grams
TRIPOD LEG SPECIFICATIONS
-
Maximum Working Height: 49 7/8" / 126.7 cm
-
Maximum Height with Column Down: 38 1/8" / 96.7 cm
-
Minimum Working Height: 9 1/4" / 23.5 cm
- Leg Angles: 20° / 50° / 80° / 180°
- Platform Diameter: 1 9/16" / 4 cm
-
Folded Length: 12 3/16" / 31 cm
-
Weight: 2 lbs 1/2 oz / .92 kg
CA Residents: Prop 65 WARNING(S)
ProMaster XC-M 525 Column Tilt Adapter
$ 34.95
ProMaster XC-M 525 Column Tilt Adapter
ProMaster SKU: 4028 | Helix SKU: PR40284
Overview
The PROMASTER 4028 Column Tilt Adapter expands the capability of your XC-M 525 aluminum or XC-M 525C carbon fiber tripod by giving its center column the freedom to tilt 180° (90° up & 90° down). This adapter essentially converts your XC-M's center column into a multi-position, adjustable boom.
Just unscrew the weight hook from the center column, loosen the center column twist lock and slide it out of the tripod. Replace it with the 4028 Column Tilt Adapter, tighten the twist lock, and open the flip lock on the Column Tilt Adapter. Insert the center column and close the flip lock. This conversion can easily be done in less than 30 seconds. That's all there is too it!
Once your XC-M 525 has been converted you can reinstall the weight hook to the bottom of the adapter and add weight for more stability. A second, retractable weight hook is included with this adapter which you can use at the end of the boom (end of the center column) to counterweight your camera.
To operate the boom, loosen the main knob on the 4028 Adapter while holding your camera and then tilt the assembly into whatever position you like before tightening the knob. To rotate the boom, loosen the twist lock on the yoke of the tripod and spin the adapter. To extend or retract the boom use the twist lock on the column to adjust its upper stage.
This adapter has a number of teeth machined within its joint to give it an excellent amount of holding power in various tilt positions. Be sure to tighten its main knob before you release your camera to prevent it from falling.
The 4028 Column Tilt Adapter can be installed and used permanently on your XC-M 525, if you so choose, because it can achieve the same vertical position as the 'normal' center column when needed.
Truth be told, this is a wicked-cool accessory. It's great for macro work, extending your camera over a tabletop or a flowing creek. And it makes other tripods highly jealous.
Specifications
- Dimensions: 5 3/4" / 146 mm long. 25mm tube diameter.
- Weight: 4 5/8 oz / 131 g
* Dimensions and weight are for the adapter sans the weight hook
ProMaster XC-M 525 Extension & Macro Legs - Aluminum
$ 29.95
ProMaster XC-M 525 Extension & Macro Legs - Aluminum
ProMaster SKU: 3559 | Helix SKU: PR35594
Overview
The PROMASTER 3559 Aluminum Extension & Macro Legs work with XC-M 525 tripods. After removing all 3 of the XC-M 525's legs these extensions attach in their place. Now you have a choice. Either reattach the legs to these extensions and you get a very stable tripod with nearly 8" more height, OR attach the 3 soft feet (included) to the extensions thereby converting your tripod into a lightweight, super-strong macro tripod.
The 3559 Extension & Macro Leg set adds amazing versatility to your XC-M 525 tripod.
Specifications
- Adds 7 7/8" / 200 mm of length to each XC-M 525 leg section
- Actual dimensions of each leg extension: 8 3/8" / 213 mm long x 25mm diameter
- Weight of each leg extension: 1 15/16 oz / 55 grams
- Weight of each foot: 9/16 oz / 16 grams
ProMaster XC-M 525 Ground Level Adapter - Aluminum
$ 15.95
ProMaster XC-M 525 Ground Level Adapter - Aluminum
ProMaster SKU: 3531 | Helix SKU: PR35310
Overview
The ProMaster 3531 Ground Level Adapter is a great accessory for getting an XC-M 525 tripod lower and closer to the ground for macro photography and a unique perspective.
Start by extending the upper stage of your XC-M's 2-stage center column. Unscrew the upper portion of the column (including the head) from the rest of the column. Now remove the weight hook and slide the lower part of the column completely out of the tripod. Replace it with the 3531 ground level adapter and insert the upper stage of the column into the 3531 adapter. Voila! In less than 30 seconds you have converted your XC-M 525 into a lowerider! You can now achieve a stable position as low as just 6 1/4" / 15.88 cm.
The Ground Level Adapter can also accept the XC-M's weight hook Just screw it into the bottom of the adapter and use it to add additional weight and stability to your XC-M 525.
FEATURES:
- Works with ProMaster XC-M 525 aluminum and XC-M 525 carbon fiber tripods
- Compatible with the XC-M 525 retractable weight hook
- Fast and easy to use
- Achieves a minimum working height of just 6 1/4" / 15.88 cm
Specifications
- Dimensions: 4 1/8" / 105 mm long | 25 mm diameter tube
- Weight: 1 13/16 oz / 51 g
ProMaster XC-M 525 Ground Level Adapter - Carbon Fiber
$ 19.95 - Sold Out
ProMaster XC-M 525 Ground Level Adapter - Carbon Fiber
ProMaster SKU: 3538 | Helix SKU: PR35389
Overview
The ProMaster 3538 Ground Level Adapter is a great accessory for getting an XC-M 525 tripod lower and closer to the ground for macro photography and a unique perspective.
Start by extending the upper stage of your XC-M's 2-stage center column. Unscrew the upper portion of the column (including the head) from the rest of the column. Now remove the weight hook and slide the lower part of the column completely out of the tripod. Replace it with the 3538 ground level adapter and insert the upper stage of the column into the 3538 adapter. Voila! In less than 30 seconds you have converted your XC-M 525 into a lowerider! You can now achieve a stable position as low as just 6 1/4" / 15.88 cm.
The Ground Level Adapter can also accept the XC-M's weight hook Just screw it into the bottom of the adapter and use it to add additional weight and stability to your XC-M 525.
FEATURES:
- Works with ProMaster XC-M 525 aluminum and XC-M 525 carbon fiber tripods
- Compatible with the XC-M 525 retractable weight hook
- Fast and easy to use
- Achieves a minimum working height of just 6 1/4" / 15.88 cm
Specifications
- Dimensions: 4 1/8" / 105 mm long | 25 mm diameter tube
- Weight: 1 9/16 oz / 44 g
ProMaster XC-M 525 Leg Warmers 3pc set - Black
$ 15.95
ProMaster XC-M 525 Leg Warmers 3pc set - Black
ProMaster SKU: 3601 | Helix SKU: PR36010
Overview
ProMaster's 3601 Leg Warmers are specifically designed for use with ProMaster XC-M 525 and XC-M 525C tripods. This kit of 3 warmers fits the 3 XC-M525 tripod legs perfectly. Simply wrap a leg warmer around the upper leg section of the tripod and zip it up. Now the leg is protected from scratches while covered in a soft sleeve. The warmers are much easier on your hands in cold weather too since they protect your skin from having direct contact with cold metal. And when you convert your XC-M tripod into its monopod mode, the warmer continues to perform as a soft, warm spot to hold on to.
Installing the leg warmers takes a bit of time and concentration since you have to line up the zipper while pulling the warmer tight around the leg. Be patient! Since it is an exact fitting item there is no slack in the fabric to ensure excellent performance once installed.
Specifications
- Actual length of each leg warmer: 8" / 203 mm
- Actual weight of each leg warmer: 5/8 oz / 18 g
ProMaster XC-M 525 Replacement Rubber Feet (set of 3)
$ 7.95
ProMaster XC-M 525 Replacement Rubber Feet (set of 3)
ProMaster SKU: 3720 | Helix SKU: PR37208
Overview
3720 is a replacement set of 3 standard feet for any XC-M 525 aluminum or carbon fiber tripod. These are a great, inexpensive replacement set if you happen to lose or damage the standard feet on an XC-M 525 tripod.
The XC-M 525 standard feet are normally installed on the tripod from the factory. They are designed to be removable, thereby exposing a 3/8"-16 threaded port on the bottom of each XC-M 525 leg. The threaded ports can be used for connecting other accessories, like the popular All Terrain Feet (ProMaster product code 3510). If you need to replace any, or all 3 of the standard feet on a ProMaster XC-M 525 tripod this set is your solution.
* Please note, these feet do not work with the XC-M522 series tripods. If you need XC-M522 standard, replacement feet please refer to ProMaster product code 3503.
Specifications
Weight: 3/16 oz / 5.4 grams - per foot
ProMaster XC-M 525 Replacement Weight Hook
$ 5.95
ProMaster XC-M 525 Replacement Weight Hook
ProMaster SKU: 3713 | Helix SKU: PR37130
Overview
The 3713 is a replacement, retractable weight hook for any XC-M 525 aluminum or carbon fiber tripod. It connects to the bottom of the center column and allows you to attach additional weight to the tripod to improve its stability.
The 3713 is also a replacement hook for the 4028 XC-M 525 Tilting Column Adapter. With the Tilting Column Adapter installed you can add weight to the bottom of the adapter as well as to the bottom of the column. This improves the overall stability of the XC-M525 tripod while also counterbalancing your camera rig.
Finally, the 3713 also works with the 3531 XC-M 525 aluminum ground level adapter and the 3538 XC-M 525 carbon fiber ground level adapter.
Specifications
Weight: 9/16 oz / 16 grams
ProMaster XC-M 525C Extension & Macro Legs - Carbon Fiber
$ 39.95
ProMaster XC-M 525C Extension & Macro Legs - Carbon Fiber
ProMaster SKU: 3566 | Helix SKU: PR35662
Overview
The PROMASTER 3566 Carbon Fiber Extension & Macro Legs work with XC-M 525C tripods. After removing all 3 of the XC-M 525C's legs these extensions attach in their place. Now you have a choice. Either reattach the legs to these extensions and you get a very stable tripod with nearly 8" more height, OR attach the 3 soft feet (included) to the extensions thereby converting your tripod into a lightweight, super-strong macro tripod.
The 3566 Extension & Macro Leg set adds amazing versatility to your XC-M 525C tripod.
Specifications
- Adds 7 7/8" / 200 mm of length to each XC-M 525C leg section
- Actual dimensions of each leg extension: 8 3/8" / 213 mm long x 25mm diameter
- Weight of each leg extension: 1 1/2 oz / 43 grams
- Weight of each foot: 9/16 oz / 16 grams
ProMaster XC-M 525CK Professional Carbon Fiber Tripod Kit with Head - Black
$ 269.95
ProMaster XC-M 525CK Professional Carbon Fiber Tripod Kit with Head - Black
ProMaster SKU: 3482 | Helix SKU: PR34825
Overview
The PROMASTER XC-M 525C tripod's 5-section, transverse legs fold 180° making the entire unit just over 15" long for storage and travel. Yet, fully extended it reaches an incredible working height of nearly 6'! Each leg's angle and length are independently adjustable, allowing the XC-M 525C to properly support your camera on uneven ground. Its dual-action ball head is strong, precise, and lightweight with an independent pan control. It has an integrated memory lock for repeatable tension control and uses ProMaster's dovetail quick release system for a fast camera connection.
The XC-M 525C is more than just a tripod, it's part of an expansive modular system.
FEATURES:
- Built-in monopod
- Transverse 180° folding legs
- Dual-action ball head with tension memory lock
- Independently adjustable leg angles
- 2-Stage, reversible center column
- Bubble levels on tripod and ball head
- Retractable weight hook
- ProMaster dovetail Q/R system (arca-swiss compatible)
- Soft, comfortable grips on touch points
- Modular design is expandable & customizable
Specifications
KIT SPECIFICATIONS
-
Maximum Working Height: 70 3/8" / 178.8 cm
-
Maximum Height with Column Down: 54 1/4" / 137.8 cm
-
Minimum Working Height: 15 1/8" / 38.4 cm *Minimum working height can be improved to 6 1/4" / 15.88 cm by adding a 3538 XC-M 525 Ground Level Adapter (sold separately)
-
Folded Length: 15" / 38.1 cm
-
Maximum Load: 17 lbs 10 oz / 8 kg
-
Weight: 2 lbs 13 5/16 oz / 1.29 kg
-
Cold Weather Performance: -4° F / -20° C
- 5-Section Carbon Fiber Legs
* Kit specifications include tripod with head attached
BALL HEAD SPECIFICATIONS
-
Height: 3 1/4" / 8.3 cm
-
Base Diameter: 1 13/16" / 4.6 cm
-
Weight: 8 5/8 oz / 245 grams
TRIPOD LEG SPECIFICATIONS
-
Maximum Working Height: 67 1/8" / 170.5 cm
-
Maximum Height with Column Down: 51" / 129.5 cm
-
Minimum Working Height: 11 7/8" / 30.1 cm
- Leg Angles: 20° / 50° / 80° / 180°
- Platform Diameter: 1 9/16" / 4 cm
-
Folded Length: 15" / 38.1 cm
-
Weight: 2 lbs 4 11/16 oz / 1.04 kg
CA Residents: Prop 65 WARNING(S)
ProMaster XC-M 525K Professional Tripod Kit with Head - Black
$ 189.95
ProMaster XC-M 525K Professional Tripod Kit with Head - Black
ProMaster SKU: 3447 | Helix SKU: PR34474
Overview
The PROMASTER XC-M 525 tripod's 5-section, transverse legs fold 180° making the entire unit just over 15" long for storage and travel. Yet, fully extended it reaches an incredible working height of nearly 6'! Each leg's angle and length are independently adjustable, allowing the XC-M 525 to properly support your camera on uneven ground. Its dual-action ball head is strong, precise, and lightweight with an independent pan control. It has an integrated memory lock for repeatable tension control and uses ProMaster's dovetail quick release system for a fast camera connection.
The XC-M 525 is more than just a tripod, it's part of an expansive modular system.
FEATURES:
- Built-in monopod
- Transverse 180° folding legs
- Dual-action ball head with tension memory lock
- Independently adjustable leg angles
- 2-Stage, reversible center column
- Bubble levels on tripod and ball head
- Retractable weight hook
- ProMaster dovetail Q/R system (arca-swiss compatible)
- Soft, comfortable grips on touch points
- Modular design is expandable & customizable
Specifications
KIT SPECIFICATIONS
-
Maximum Working Height: 70 3/8" / 178.8 cm
-
Maximum Height with Column Down: 54 1/4" / 137.8 cm
-
Minimum Working Height: 15 1/8" / 38.4 cm *Minimum working height can be improved to 6 1/4" / 15.88 cm by adding a 3531 XC-M 525 Ground Level Adapter (sold separately)
-
Folded Length: 15" / 38.1 cm
-
Maximum Load: 17 lbs 10 oz / 8 kg
-
Weight: 3 lbs 4 7/8 oz / 1.5 kg
-
Cold Weather Performance: -4° F / -20° C
- 5-Section Aluminum Legs
* Kit specifications include tripod with head attached
BALL HEAD SPECIFICATIONS
-
Height: 3 1/4" / 8.3 cm
-
Base Diameter: 1 13/16" / 4.6 cm
-
Weight: 8 5/8 oz / 245 grams
TRIPOD LEG SPECIFICATIONS
-
Maximum Working Height: 67 1/8" / 170.5 cm
-
Maximum Height with Column Down: 51" / 129.5 cm
-
Minimum Working Height: 11 7/8" / 30.1 cm
- Leg Angles: 20° / 50° / 80° / 180°
- Platform Diameter: 1 9/16" / 4 cm
-
Folded Length: 15" / 38.1 cm
-
Weight: 2 lbs 12 1/4 oz / 1.25 kg
CA Residents: Prop 65 WARNING(S)
ProMaster XC-M 525K Professional Tripod Kit with Head - Blue
$ 189.95
ProMaster XC-M 525K Professional Tripod Kit with Head - Blue
ProMaster SKU: 4077 | Helix SKU: PR40772
Overview
The PROMASTER XC-M 525 tripod's 5-section, transverse legs fold 180° making the entire unit just over 15" long for storage and travel. Yet, fully extended it reaches an incredible working height of nearly 6'! Each leg's angle and length are independently adjustable, allowing the XC-M 525 to properly support your camera on uneven ground. Its dual-action ball head is strong, precise, and lightweight with an independent pan control. It has an integrated memory lock for repeatable tension control and uses ProMaster's dovetail quick release system for a fast camera connection.
The XC-M 525 is more than just a tripod, it's part of an expansive modular system.
FEATURES:
- Built-in monopod
- Transverse 180° folding legs
- Dual-action ball head with tension memory lock
- Independently adjustable leg angles
- 2-Stage, reversible center column
- Bubble levels on tripod and ball head
- Retractable weight hook
- ProMaster dovetail Q/R system (arca-swiss compatible)
- Soft, comfortable grips on touch points
- Modular design is expandable & customizable
Specifications
KIT SPECIFICATIONS
-
Maximum Working Height: 70 3/8" / 178.8 cm
-
Maximum Height with Column Down: 54 1/4" / 137.8 cm
-
Minimum Working Height: 15 1/8" / 38.4 cm *Minimum working height can be improved to 6 1/4" / 15.88 cm by adding a 3531 XC-M 525 Ground Level Adapter (sold separately)
-
Folded Length: 15" / 38.1 cm
-
Maximum Load: 17 lbs 10 oz / 8 kg
-
Weight: 3 lbs 4 7/8 oz / 1.5 kg
-
Cold Weather Performance: -4° F / -20° C
- 5-Section Aluminum Legs
* Kit specifications include tripod with head attached
BALL HEAD SPECIFICATIONS
-
Height: 3 1/4" / 8.3 cm
-
Base Diameter: 1 13/16" / 4.6 cm
-
Weight: 8 5/8 oz / 245 grams
TRIPOD LEG SPECIFICATIONS
-
Maximum Working Height: 67 1/8" / 170.5 cm
-
Maximum Height with Column Down: 51" / 129.5 cm
-
Minimum Working Height: 11 7/8" / 30.1 cm
- Leg Angles: 20° / 50° / 80° / 180°
- Platform Diameter: 1 9/16" / 4 cm
-
Folded Length: 15" / 38.1 cm
-
Weight: 2 lbs 12 1/4 oz / 1.25 kg
ProMaster XC-M 525K Professional Tripod Kit with Head - Red
$ 189.95
ProMaster XC-M 525K Professional Tripod Kit with Head - Red
ProMaster SKU: 3468 | Helix SKU: PR34689
Overview
The PROMASTER XC-M 525 tripod's 5-section, transverse legs fold 180° making the entire unit just over 15" long for storage and travel. Yet, fully extended it reaches an incredible working height of nearly 6'! Each leg's angle and length are independently adjustable, allowing the XC-M 525 to properly support your camera on uneven ground. Its dual-action ball head is strong, precise, and lightweight with an independent pan control. It has an integrated memory lock for repeatable tension control and uses ProMaster's dovetail quick release system for a fast camera connection.
The XC-M 525 is more than just a tripod, it's part of an expansive modular system.
FEATURES:
- Built-in monopod
- Transverse 180° folding legs
- Dual-action ball head with tension memory lock
- Independently adjustable leg angles
- 2-Stage, reversible center column
- Bubble levels on tripod and ball head
- Retractable weight hook
- ProMaster dovetail Q/R system (arca-swiss compatible)
- Soft, comfortable grips on touch points
- Modular design is expandable & customizable
Specifications
KIT SPECIFICATIONS
-
Maximum Working Height: 70 3/8" / 178.8 cm
-
Maximum Height with Column Down: 54 1/4" / 137.8 cm
-
Minimum Working Height: 15 1/8" / 38.4 cm *Minimum working height can be improved to 6 1/4" / 15.88 cm by adding a 3531 XC-M 525 Ground Level Adapter (sold separately)
-
Folded Length: 15" / 38.1 cm
-
Maximum Load: 17 lbs 10 oz / 8 kg
-
Weight: 3 lbs 4 7/8 oz / 1.5 kg
-
Cold Weather Performance: -4° F / -20° C
- 5-Section Aluminum Legs
* Kit specifications include tripod with head attached
BALL HEAD SPECIFICATIONS
-
Height: 3 1/4" / 8.3 cm
-
Base Diameter: 1 13/16" / 4.6 cm
-
Weight: 8 5/8 oz / 245 grams
TRIPOD LEG SPECIFICATIONS
-
Maximum Working Height: 67 1/8" / 170.5 cm
-
Maximum Height with Column Down: 51" / 129.5 cm
-
Minimum Working Height: 11 7/8" / 30.1 cm
- Leg Angles: 20° / 50° / 80° / 180°
- Platform Diameter: 1 9/16" / 4 cm
-
Folded Length: 15" / 38.1 cm
-
Weight: 2 lbs 12 1/4 oz / 1.25 kg
CA Residents: Prop 65 WARNING(S)
ProMaster XC-M All Terrain Feet (set of 3)
$ 29.95
ProMaster XC-M All Terrain Feet (set of 3)
ProMaster SKU: 3510 | Helix SKU: PR35105
Overview
The PROMASTER 3510 ALL TERRAIN FEET are a serious upgrade for any XC-M tripod.
Once the standard feet are removed (simply pull them off the bottom of each XC-M leg while applying a little bit of wiggle action) you can install the stainless-steel spikes into the threaded port found at the bottom of each XC-M leg. An included wrench will help you to tighten the spikes in place. These spikes are great for solid footing on ice, dirt, grass, and more. But what if you find your XC-M's legs sinking into soft ground like sand or snow? Never fear! Just attach the sand/snow baskets directly to the spikes for excellent stability on soft ground.
Finally, 3 soft tips are included with this kit for use on delicate surfaces such as wood floors. The soft tips push onto the spikes and can be applied either with, or without the sand/snow baskets in installed.
This kit is truly one of the most versatile accessories for using your tripod on any kind of terrain. It is designed for ProMaster XC-M 522 and XC-M525 aluminum and carbon fiber tripods.
Specifications
- Weight of 1, fully assembled foot: 42 grams
- Weight of 1 spike only: 24 grams
- Weight of 1 sand / snow basket only: 8 grams
- Weight of 1 soft tip only: 10 grams
ProMaster XC-M Hipster & Strap
$ 29.95
ProMaster XC-M Hipster & Strap
ProMaster SKU: 3587 | Helix SKU: PR35877
Overview
The ProMaster Hipster and Strap works with all models of XC-M tripods. This unique system offers multiple ways of carrying a tripod. There are two parts to this system, the Hipster and the strap.
The Hipster is a holster which allows two of the tripod's legs to slide into it while one leg overlaps the front so the tripod can be removed lightning fast. The Hipster easily attaches to a belt or camera bag/backpack using its Velcro-loop attachment on its back side. The Hipster also has two metal D-rings which act as quick-connection points for the strap. Using the quick release metal buckles on the strap you can attach the Hipster and carry your tripod over your shoulder.
The shoulder strap has a soft shoulder pad for comfortable carrying. It also has a tool pouch built-in, which is a great way to carry spare wrenches for adjustments in the field. Since every XC-M includes a tool kit, the integrated pouch on this strap is a very convenient way of storing and carrying those tools.
But wait, there's more! Inside of the Hipster is a sewn-in pocket. When wearing the Hipster on your belt in front of your body, you can convert your XC-M into a monopod and place the foot of the monopod into this pocket for stability. This makes a great stabilizing rig, especially for videography.
ProMaster XC-M Shoulder Strap
$ 19.95
ProMaster XC-M Shoulder Strap
ProMaster SKU: 3580 | Helix SKU: PR35808
Overview
This shoulder strap works with all ProMaster XC-M tripods. It quickly attaches the the machined strap slot in the yoke of an XC-M tripod using a quick release buckle. The other side of the strap slides around the lower portion of the tripod's legs like a lasso.
The XC-M shoulder strap has a soft shoulder pad for comfortable carrying. It also has a tool pouch built-in, which is a great way to carry spare wrenches for adjustments in the field. Since every XC-M includes a tool kit the integrated pouch on this strap is a very convenient way of storing and carrying those tools.
Specifications
- Length: 45" / 114 cm - maximum overall length of strap, including buckle, when adjusted to its longest position.
ProMaster XC-MH26 Ball Head - Black
$ 79.95
ProMaster XC-MH26 Ball Head - Black
ProMaster SKU: 3489 | Helix SKU: PR34894
Overview
The PROMASTER XC-MH26 BALL HEAD is well featured, technical ball head with incredible strength in a compact and lightweight form factor. It is made of machined (not cast) high grade aluminum.
The XC-MH26's dual action design uses separate knobs to adjust the ball tension and the panning control. An etched, numbered scale is applied to the base of this head for precise panning movements. The tension control knob has an integrated memory lock dial which allows you to set a repeatable tension stop. Its quick release system uses a dovetail style plate (arca-type) with safety bolts. All knobs are covered in a soft yet grippy material that is comfortable and easy on your fingers, even in cold weather. Multiple bubble levels (1 bullseye and 2 line levels) are integrated so you can precisely level your camera in either a horizontal or vertical position. The included quick release plate has a strap slot which is compatible with a variety of straps and hand grips.
Specifications
INCLUDES:
- 1 XC-M26 Ball Head
- 1 3608 Quick Release Plate
SPECIFICATIONS:
-
Height: 3 1/4" / 8.3 cm
-
Base Diameter: 1 5/8" / 4.1 cm
-
Weight: 8 oz / 226 grams
- Maximum Load: 11 lbs / 5 kg
- Cold Weather Performance: -4° F / -20° C
CA Residents: Prop 65 WARNING(S)
ProMaster XC-MH30 Ball Head - Black
$ 89.95
ProMaster XC-MH30 Ball Head - Black
ProMaster SKU: 3496 | Helix SKU: PR34962
Overview
The PROMASTER XC-MH30 BALL HEAD is well featured, technical ball head with incredible strength in a compact and lightweight form factor. It is made of machined (not cast) high grade aluminum.
The XC-MH30's dual action design uses separate knobs to adjust the ball tension and the panning control. An etched, numbered scale is applied to the base of this head for precise panning movements. The tension control knob has an integrated memory lock dial which allows you to set a repeatable tension stop. Its quick release system uses a dovetail style plate (arca-type) with safety bolts. All knobs are covered in a soft yet grippy material that is comfortable and easy on your fingers, even in cold weather. Multiple bubble levels (1 bullseye and 2 line levels) are integrated so you can precisely level your camera in either a horizontal or vertical position. The included quick release plate has a strap slot which is compatible with a variety of straps and hand grips.
Specifications
INCLUDES:
- 1 XC-MH30 Ball head
- 1 3608 Quick Release Plate
SPECIFICATIONS:
-
Height: 3 1/4" / 8.3 cm
-
Base Diameter: 1 13/16" / 4.6 cm
-
Weight: 8 5/8 oz / 245 grams
- Maximum Load: 17 lbs 10 oz / 8 kg
- Cold Weather Performance: -4° F / -20° C
CA Residents: Prop 65 WARNING(S)
ProMaster XtraPower AA Battery Case
$ 4.95
ProMaster XtraPower AA Battery Case
ProMaster XtraPower AC Replacement Cord
$ 9.95
ProMaster XtraPower AC Replacement Cord
ProMaster XtraPower PRECHARGED AA Battery & Charger Kit
$ 49.95
ProMaster XtraPower PRECHARGED AA Battery & Charger Kit
ProMaster XtraPower USB Charging Kit
$ 19.95
ProMaster XtraPower USB Charging Kit
