Azden 1201 Series System (1201VMX)
$ 1,199.00
Azden 1201VMX Series System
The Azden 1201VMX wireless microphone system combines the 1201URX/VM (V-Mount) receiver with the 1201XT plug-in transmitter.
The Azden 1201URX/VM Receiver comes equipped with a V-Mount adapter for direct mounting on your camera's battery. In addition to the receiver's slot-in design, the 1201-series also offers 188 user selectable, DTV compliant frequencies. True-diversity technology with two complete front-ends and high-gain antennas maximize reception and range while greatly reducing interference and drop-out. The transmitter features a multi-function digital display and rugged construction. 12VDC power is supplied from the camera.
The Azden 1201XT Plug-in Transmitter is designed for use with the 1201 Series receivers. The 1201-series offers 188 user selectable, DTV compliant frequencies. A 3-pin XLR connector accommodates your favorite microphone and provides +48V phantom power if needed. There is a multi-function digital display, and its rugged construction ensures reliable use outdoors, on the road, etc. The transmitter is powered via 2-AA alkaline batteries for up to 8-hours.
Features
- V-Mount battery adapter case
- Plug-in transmitter works w/ any 3-pin XLR mic
- 188 DTV frequencies / 4 UHF TV bands
- True diversity system
- Improved image rejection, S/N ratio & superior diversity isolation
- Multi-function LCD shows channel, frequency, battery info, AF level, and diversity operation
Specifications
1201URX/VM
- RF Carrier Frequency Range: 188 steps ~ 638.125 – 661.875 MHz
- Micro Computer Controlled PLL Synth.
- Noise Reduction: Expander (THAT)
- Effective Operating Range: 200 – 300 ft ~ 60 – 100m
- Frequency Response: 50 – 15kHz (± 1.5dB)
- RF Sensitivity: (12dB SINAD) 1.2μV
- Adjacent Channel Selectivity: > 70dB (± 250kHz)
- Image Rejection: > 93dB
- IF Rejection: > 93dB
- Audio THD: 62dB (± 5kHz Deviation) “A” Weighted
- Power Requirements: 11 – 15V DC @ 220mA
- Dimensions: 82W x 150H x 60D mm – 1201URX/VM
- Operating Temperature Range: -50 – +122 F ~ -10 – +50 C
- Weight: 26.45ounces ~ 750g for 1201URX/VM
1201XT
- Output Power: 30mW
- Max Modulation Sensitivity: +20dBM ~ 0dBm
- MIC Level / Imped. (Dynamic): -60dBm / 2.2kΩ (± 5kHz Dev.)
- Phantom Power: 48V ±2V @ 2mA
- Power Requirements: 3V DC (2 “AA” Alkaline) @ < 180mA – 290 mA w/Phantom Power ON
- Dimensions: 1.57 (W) x 4.49 (H) x 1.57 (D) inches
- 40 (W) x 114 (H) x 40 (D) mm
- Weight w/Battery: 6.35 ounces ~ 180g
In the Box
- 1201URX/VM receiver
- 1201XT plug-in transmitter
- Hardshell carrying case
- Manual
Azden EX-505U UNI-Directional Lavalier - NEW
$ 36.00
Azden EX-505U UNI-Directional Lavalier - NEW
Azden’s lapel microphones offer professional performance at a very affordable price, making them a great choice for almost any situation where clear speech capture is needed. Whether you need a high quality audio option for on-camera interviews, film projects, wedding videos, YouTube videos, web-casting, theater performances or lectures, Azden has the solution for you!
The EX-505U Lapel Microphone is a high quality, electret condenser microphone. The microphone element is uni-directional, meaning it picks up sound most strongly from the top. Its directional sound pick up is perfect for situations where you want to isolate a speaker’s voice from background noise or reduce the potential for feedback over a speaker system.
No matter what the application, Azden’s lapel microphones can help your project reach its full potential!
Specifications:
- Mic Type: Electret Condenser
- Frequency Response: 30-18,000Hz
- Directionality: Uni-directional
- Sensitivity: -49dB at 1kHz (0dB=1V/Pa)
- Impedance: 2.2kΩ (at 1kHz)
- Power Requirement: Plug-in power DC 1-10V
- Weight: Approx. 0.35 oz.
- Connector: TS (Tip Sleeve) right angle 3.5mm mini-plug with 1.3m cable
- Detachable windscreen
Azden SGM-1X Professional Shotgun Microphone
$ 178.95
The SGM-1X Professional Shotgun Microphone is designed to provide quality audio for the videographer. It is ideal for today's smaller, digital video cameras where longer models would appear in the frame when camera mounted. The hyper-directional super-cardioid shotgun microphone has a wide frequency response, exhibits low noise and accepts up to 110dB SPL input levels. The 11.8" long microphone uses a single AAA battery that will last over 1000 hours due to the mic's extremely low current drain.
Azden SGM-990 Supercardioid / omni shotgun mic w/ 2-position switch - New
$ 85.95
Azden SGM-990 Supercardioid / omni shotgun mic w/ 2-position switch - New
The SGM-990 features a 2-position switch to select between directional pickup patterns to focus on your sound source. Choose between "Long" for supercardioid or "Short" for a cardioid pickup pattern, depending on the distance from your subject. Both settings will provide rejection of unwanted sound from the sides and the back. The SGM-990's working range is 20 to 40 feet and it has a frequency response of 150 Hz to 18 kHz. It is built with a coiled cable which has a 1/8" (3.5mm) mini-jack connector, and uses one alkaline AAA battery for power. A windscreen and shoe mount are included.
Azden WMS-PRO Wireless Microphone System
$ 158.95
The "all-time" best selling wireless microphone for videography. This versatile system consists of the WM-PRO belt-pack transmitter 2 plug-in electret condenser microphones, a lavalier (EX-503) and handheld (EX-413) and the WR-PRO receiver which comes with both shoe-mount and hook and loop fastener. All receivers and transmitters in the "PRO" Series are on the same 2 frequencies (169.445MHz and 170.245MHz).
RODE Broadcaster Condenser Microphone
$ 419.00 - Sold Out
RODE Broadcaster Condenser Microphone
Rode SKU: Broadcaster | Helix SKU: RMBroadcaster
Overview
Precision 1" broadcast cardioid end-address condenser microphone. Features unique 'on air' indicator.
The RØDE Broadcaster is a large diaphragm, end-address condenser microphone designed to provide the ultimate performance for broadcast vocal applications.
Its rich, full quality tailored response has an emphasised proximity effect that has made it a standard in radio stations the world over. It is equally suitable as a voice-over microphone for film and television
The Broadcaster features an internal pop filter, designed to minimise plosives sounds that can overload the microphone capsule and distort the audio output. In addition to the Broadcaster's native 20Hz-20kHz response, a selectable high-pass filter at 75Hz is available which will prevent low-end noise such as air conditioners and traffic from being recorded.
The Broadcaster features an innovative 'On-Air' indicator on the body that can be wired for external activation by the 'Channel On/Mute' function on many consoles. If not connected to a console or switch, the indicator will remain lit whenever the microphone has power.
The RØDE Broadcaster microphone is designed and made in Australia, and covered by RØDE Microphones' industry leading 10 year warranty.
Specifications
| Acoustic Principle | Pressure Gradient |
| Active Electronics | JFET impedance converter with bipolar output buffer |
| Capsule | 1.00" |
| Polar Pattern |  |
| Address Type | End |
| Frequency Range | 20Hz - 20kHz |
| Output Impedance | 40Ω |
| Maximum SPL | 128dB SPL (@ 1kHz, 1% THD into 1KΩ load) |
| Maximum Output Level | 2.0mV |
| Sensitivity | -34.0dB re 1 Volt/Pascal (20.00mV @ 94 dB SPL) +/- 2 dB @ 1kHz |
| Equivalent Noise Level (A-weighted) | 14dB-A |
| Power Options |
+24V phantom power required from mixer or interface
|
| Weight | 577.00gm |
| Dimensions | 167.00mmH x 50.00mmW x 65.00mmD |
| Output |  |
| Warranty | 1 year with free extension to 10 years following registration |
Rode Directional Microphone for iPhone and iPad VideoMic Me
$ 59.00 - Sold Out
Rode Directional Microphone for iPhone and iPad VideoMic Me
The VideoMic Me is a compact and lightweight, high-quality directional microphone with that connects directly to the iPhone TRRS microphone/headphone socket. Its flexible mounting bracket accommodates a wide range of smartphones and allows the microphone to be fitted for primary camera or front camera ('selfie') use. A 3.5mm headphone jack on the rear allows for play-through of audio while recording (app dependent) as well as easy playback of your videos without having to remove the microphone. The VideoMic Me includes a deluxe furry windshield for shooting outdoors or in adverse weather.
| Acoustic Principle | Pressure Gradient |
| Active Electronics | JFET impedance converter |
| Capsule | 0.50" |
| Polar Pattern | |
| Address Type | End |
| Frequency Range | 100Hz - 20kHz |
| Maximum SPL | 140dB SPL (@ 1kHz, 1% THD into 1KΩ load) |
| Sensitivity | -33.0dB re 1 Volt/Pascal (22.00mV @ 94 dB SPL) +/- 2 dB @ 1kHz |
| Equivalent Noise Level (A-weighted) | 20dB-A |
| Power Options | |
| Weight | 34gm |
| Dimensions | 38mmH x 21mmW x 80mmD |
| Output |  |
| Warranty | 1 year with free extension to 2 years following registration |
RODE HS1-P Headset Microphone (Pink)
$ 299.00 - Sold Out
Ultra lightweight and ergonomic omnidirectional headset microphone (pink).
- Ultra discreet appearance
- Available in Pink or Black
- Omni-directional polar pattern
- Three axes of mechanical adjustment for perfect fit with malleable tube arm and headband for finer adjustment
- Lightweight construction for complete comfort
- Corrosion resistant stainless steel tube arm
- Low handling noise
- Includes Mini-furry and pop filter / windshield
- RØDE MiCon interconnectivity system provides interface with a wide range of wireless systems
- Five year extended warranty when you register your microphone
The RØDE HS1 is a discreet and lightweight headset microphone that provides clean, clear and pronounced audio for any application where the microphone needs to be in close proximity to presenter's mouth.
Subtle, ergonomic design including three axes of mechanical adjustment, a malleable, ultra lightweight tube arm and headband, and the choice of either black (HS1-B) or pink (HS1-P) models ensure the perfect fit and function for each individual.
The HS1's light weight, comfortable fit, low self-noise, minimal appearance and user friendly omni-directional polar pattern make it an ideal microphone for film, television, video, theatre, house of worship and live vocal performance.
The headset is connected via a 1.2m (4') shielded, detachable Kevlar® reinforced cable that has been rigorously strain tested up to 10kg to ensure reliable performance. Integrated cable management on the retainer body and an additional cable management clip minimises visibility, while providing maximum mobility for the wearer.
The included mini-furry for high wind protection ensures quality recordings in adverse environments, and the supplied anti-trauma water resistant case provides rugged and secure protection for the microphone, cable, clips and included accessories and tools.
Knowing that versatility is paramount in any product, RØDE has developed the MiCon™ connector system which provides seamless integration between the HS1 headset microphone and a wide range of wireless systems as well as consoles, cameras and portable recorders.
The RØDE HS1 headset is designed and made in Australia, and is covered by RØDE Microphones' innovative 5 year 'no questions asked' warranty which provides 12 months of complete cover, and an optional US$99 replacement microphone during the extended warranty period.
| Acoustic Principle | Pressure Gradient |
| Active Electronics | JFET impedance converter |
| Capsule | 0.10" |
| Polar Pattern |  |
| Address Type | End |
| Frequency Range | 60Hz - 18kHz |
| Output Impedance | 3000Ω |
| Maximum SPL | 122dB SPL (@ 1kHz, 1% THD into 1KΩ load) |
| Maximum Output Level | 189.0mV |
| Sensitivity | -47.2dB re 1 Volt/Pascal (21.00mV @ 94 dB SPL) +/- 2 dB @ 1kHz |
| Equivalent Noise Level (A-weighted) | 36dB-A |
| Power Options | |
| Weight | 6.50gm |
| Dimensions | 65.00mmH x 180.00mmW x 200.00mmD |
| Output |  |
| Warranty | 1 year with free extension to 5 years following registration here |
IN THE BOX:
RODE invisiLav Discreet Lavalier Mounting System (10-Pack)
$ 40.00 - Sold Out
Discreet skinsafe mount for lavalier microphones. Supports RODE Lavalier and smartLav. Pack of 10.
The RØDE invisiLav is designed to aid the concealing of the Lavalier and smartLav microphones. Its soft construction absorbs noise and vibration, while the wide, flat profile provides coverage from the elements and allows for versatile mounting. There's two mounting points in case a redundant mic is required, and cable management on the side. Available in either a pack of three or a bulk pack of ten, the invisiLav comes with pre-cut, skinsafe adhesive that can be used to stick the invisiLav to either the body or to fabric. The invisiLav itself is also made from a medical grade skin safe material so it can be mounted on the body without fear of irritation.
| Weight | 5.00gm |
| Dimensions | 18.00mmH x 25.00mmW x 6.00mmD |
| Warranty | 1 year |
RODE iXY-L Stereo Microphone (Lightning Connector)
$ 199.00 - Sold Out
RODE iXY-L Stereo Microphone (Lightning Connector)
Rode SKU: iXY-L | Helix SKU: RMiXYL
Overview
Digital stereo microphone (up to 24/96K recording) for lightning-compatible Apple devices including iPhone 5, 5s & 5c. Supplied with carry case and windshield.
- Record stereo audio at 24-bit, 96kHz*
- Matched pair of 1/2" cardioid condenser capsules
- Metal casing for enhanced durability and electromagnetic interference immunity.
- Includes windshield, zip case
- Software-switchable 72Hz high pass filter for reduction of unwanted low frequency noise.
- iXY-L compatible with iPhone 5, iPhone 5s, iPhone 5c, iPhone 6 and iPhone 6plus.
- iXY-30PIN compatible with iPhone 4s and earlier
- Twelve month warranty
The RØDE i-XY is the ultimate recording microphone for iPhone® and iPad®. With up to 24-bit/96k* recording and on-board high-fidelity A/D conversion, your i-XY recordings are rich, smooth and accurate. At the heart of the i-XY is a matched pair of ½” cardioid condenser capsules, fixed in a perfect 90 degree ‘near-coincident’ alignment. This results in immersive and true-to-life stereo recordings, captured in incredibly high detail. Designed and manufactured in Australia, the i-XY is available in two versions - Lightning and 30-pin. The Lightning version supports the iPhone® 5s, iPhone® 5 and iPhone® 5c. The 30-pin version supports the iPhone® 4S, iPhone® 4, iPad® (3rd generation) and iPad® 2. A foam windshield is supplied for outdoor recording as well as a reinforced protective zip case to ensure your i-XY is available whenever you need it. *RØDE Rec or RØDE Rec LE app required for 24/96 quality. iPhone and iPad are trademarks of Apple Inc., registered in the U.S. and other countries.
Specifications
| Acoustic Principle | Pressure Gradient |
| Capsule | 0.50" |
| Polar Pattern |
|
| Address Type | End |
| Frequency Range | 20Hz - 20kHz |
| Output Impedance | 0Ω |
| Maximum SPL | 120dB SPL (@ 1kHz, 1% THD into 1KΩ load) |
| Sensitivity | -42.0dB re 1 Volt/Pascal (8.52mV @ 94 dB SPL) +/- 2 dB @ 1kHz |
| Equivalent Noise Level (A-weighted) | 18dB-A |
| Weight | 40.00gm |
| Dimensions | 46.00mmH x 55.00mmW x 40.00mmD |
| Warranty | 1 year |
What's in the Box
|
i-XY (Lightning Version) Stereo Microphone for Apple iPhone® & iPad® |
 |
Wind Shield |
 |
Zip Pod |
RODE Lav-Headset Headset mount for Lavalier Microphones - Junior Size
$ 25.00 - Sold Out
Headset mount for Lavalier Microphones. Compatible with RØDE Lavalier and smartLav+. Junior size.
The Lav-Headset is an innovative and ergonomic headset-style wearable mount that offers increased versatility for users of the RØDE Lavalier and smartLav+ lapel microphones. It allows the microphone to be worn in close proximity to the mouth for optimal audio performance.
Engineered from spring steel that has been plated for lifelong durability, the mount is designed to hold its shape throughout the rigors of repeated use. Integrated cable management at the rear of the mount ensures that the microphone cable is tightly secured and provides strain relief.
The Lav-headset is available in three sizes to comfortably accommodate a range of head sizes. As a general guide the sizes are:
- Junior – Ages up to 13
- Medium – Teen to Adult
- Large – Larger Adult
Lav-Headset Specifications:
| Weight | 5gm |
| Dimensions | 100mmH x 140mmW x 200mmD |
| Warranty | 1 year |
RODE Lav-Headset Headset mount for Lavalier Microphones - Large Size
$ 25.00 - Sold Out
Headset mount for Lavalier Microphones. Compatible with RØDE Lavalier and smartLav+. Large size.
The Lav-Headset is an innovative and ergonomic headset-style wearable mount that offers increased versatility for users of the RØDE Lavalier and smartLav+ lapel microphones. It allows the microphone to be worn in close proximity to the mouth for optimal audio performance.
Engineered from spring steel that has been plated for lifelong durability, the mount is designed to hold its shape throughout the rigors of repeated use. Integrated cable management at the rear of the mount ensures that the microphone cable is tightly secured and provides strain relief.
The Lav-headset is available in three sizes to comfortably accommodate a range of head sizes. As a general guide the sizes are:
- Junior – Ages up to 13
- Medium – Teen to Adult
- Large – Larger Adult
Lav-Headset Specifications:
| Weight | 5gm |
| Dimensions | 100mmH x 140mmW x 200mmD |
| Warranty | 1 year |
RODE Lav-Headset Headset mount for Lavalier Microphones - Medium Size
$ 25.00 - Sold Out
Headset mount for Lavalier Microphones. Compatible with RØDE Lavalier and smartLav+. Medium size.
The Lav-Headset is an innovative and ergonomic headset-style wearable mount that offers increased versatility for users of the RØDE Lavalier and smartLav+ lapel microphones. It allows the microphone to be worn in close proximity to the mouth for optimal audio performance.
Engineered from spring steel that has been plated for lifelong durability, the mount is designed to hold its shape throughout the rigors of repeated use. Integrated cable management at the rear of the mount ensures that the microphone cable is tightly secured and provides strain relief.
The Lav-headset is available in three sizes to comfortably accommodate a range of head sizes. As a general guide the sizes are:
- Junior – Ages up to 13
- Medium – Teen to Adult
- Large – Larger Adult
Lav-Headset Specifications:
| Weight | 5gm |
| Dimensions | 100mmH x 140mmW x 200mmD |
| Warranty | 1 year |
Support
RODE M1 Dynamic Handheld Stage Microphone
$ 99.00 - Sold Out
RODE M1 Dynamic Handheld Stage Microphone
Rode SKU: M1 | Helix SKU: RMM1
Overview
M1 Live performance cardioid dynamic microphone with lifetime warranty
- Live dynamic vocal microphone
- High output neodymium capsule
- Cardioid polar pattern
- Balanced, low impedance output
- Ergonomically designed heavy duty all-metal body
- Low handling noise
- Lifetime warranty when you register your microphone
With rock-solid build quality and a high-power neodymium capsule, the RØDE M1 live dynamic microphone is designed to provide the very best performance, night after night. Its durability is backed-up by a lifetime warranty, following registration of purchase.
The M1's ergonomically designed all-metal body is engineered for maximum comfort when used as a handheld microphone. It feels robust, solid and perfectly balanced without being heavy, and handling noise is almost completely eliminated by the microphone's internal design.
Featuring a warm response that is incredibly defined for a dynamic microphone, the M1's smooth character and defined clarity offer incredible performance as a live vocal microphone. A tightly controlled cardioid polar pattern minimises spill and feedback.
Renowned as one of the industry's best live vocal microphones, the M1 is an equally strong performer on guitar amplifiers as well as kick drum, snare drum, toms and percussion.
Specifications
| Acoustic Principle | Dynamic |
| Polar Pattern | |
| Address Type | End |
| Frequency Range | 75Hz - 18kHz |
| Output Impedance | 320Ω |
| Sensitivity | -56.0dB re 1 Volt/Pascal (1.60mV @ 94 dB SPL) +/- 2 dB @ 1kHz |
| Weight | 360.00gm |
| Dimensions | 171.00mmH x 51.50mmW x 51.50mmD |
| Output | |
| Warranty | 1 year with free extension to lifetime warranty following registration |
RODE M1-S Dynamic Live Performance Lockable Low-Noise Switch
$ 115.00 - Sold Out
RODE M1-S Dynamic Live Performance Lockable Low-Noise Switch
Rode SKU: M1-S | Helix SKU: RMM1S
Overview
M1-S Switchable live performance cardioid dynamic microphone. Fully lockable low-noise switch.
- Live dynamic vocal microphone
- High output neodymium capsule
- Cardioid polar pattern
- Lockable on/off switch
- XLR security lock
- Ergonomically designed heavy duty all-metal body
- Low handling noise
- 10 year extended warranty when you register your microphone
With rock-solid build quality and a high-power neodymium capsule, the RØDE M1-S switchable live dynamic microphone is designed to provide the very best performance, night after night. Its durability is backed-up by a ten year warranty, following registration of purchase.
The M1's ergonomically designed all-metal body is engineered for maximum comfort when used as a handheld microphone. It feels robust, solid and perfectly balanced without being heavy, and handling noise is almost completely eliminated by the microphone's internal design.
Featuring a warm response that is incredibly defined for a dynamic microphone, the M1's smooth character and defined clarity offer incredible performance as a live vocal microphone. A tightly controlled cardioid polar pattern minimises spill and feedback.
The addition of an on/off switch adds versatility for artists, engineers and presenters that prefer control while on stage. A flush-mounted lock ensures the microphone cannot be accidentally switched.
For additional security the M1-S features an XLR lock that can be used to fix the microphone to the cable.
Renowned as one of the industry's best live vocal microphones, the M1 is an equally strong performer on guitar amplifiers as well as kick drum, snare drum, toms and percussion.
Specifications
Rode M2 Handheld Condenser Microphone
$ 179.00 - Sold Out
Rode M2 Handheld Condenser Microphone
Rode SKU: M2 | Helix SKU: RMM2
Overview
The RØDE M2 is a rugged live-performance condenser microphone designed to provide a full frequency response and premium performance on stage. Combining sound quality equal to that of the finest studio microphones, the M2 live performance handheld condenser microphone benefits from RØDE’s extensive experience. With features such as integrated shock mounting to reduce handling noise and a tailored response to reduce feedback, the M2 is a sturdy and versatile addition to your live microphone kit.
Featuring a tailored-for-stage super-cardioid polar pattern and an internally shock mounted 1/2" condenser capsule, the M2 provides a high quality alternative to dynamic microphones for live performance. The addition of an on/off switch adds versatility for artists that prefer greater control over their sound, while a lock ensures that the microphone cannot be accidentally switched.
The RØDE M2 live condenser microphone is designed and made in Australia, and covered by RØDE Microphones' industry leading 10 year warranty.
- Live condenser vocal microphone
- Feedback rejecting super-cardioid pick up pattern
- Locking on/off switch
- Heavy duty metal body
- High level of RF rejection
- Low handling noise
- RM1 stand mount and ZP1 zip pouch included
Specifications
| Acoustic Principle | Pressure Gradient |
| Active Electronics | JFET impedance converter with bipolar output buffer |
| Capsule | 0.50" |
| Polar Pattern |  |
| Address Type | End |
| Frequency Range | 35Hz - 20kHz |
| Output Impedance | 50Ω |
| Maximum SPL | 141dBSPL |
| Maximum Output Level | 5.2mV (@ 1kHz, 1% THD into 1KΩ load) |
| Sensitivity | -44.0dB re 1 Volt/Pascal (6.30mV @ 94 dB SPL) +/- 2 dB @ 1kHz |
| Equivalent Noise Level (A-weighted) | 23dBA |
| Power Options |
|
| Weight | 308.00g |
| Dimensions | 187.00mmH x 47.00mmW x 47.00mmD |
| Output | |
| Warranty | 1 year with free extension to 10 years following registration |
RODE M3 Multi-Powered Cardioid Condenser Microphone
$ 149.00 - Sold Out
RODE M3 Multi-Powered Cardioid Condenser Microphone
Rode SKU: M3 | Helix SKU: RMM3
Overview
Studio and location multi-powered cardioid condenser microphone with switchable HPF and PAD.
- Heavy duty metal body
- Internal capsule shock mount
- High level of RF rejection
- On-mic selectable high pass filter @ 80Hz-12dB/Oct (-10 and -20dB PAD)
- Heat-treated high-strength mesh head
- Battery status indicator
- 9V Battery Power and 24 - 48V phantom power
- Includes wind shield, mic clip and zip pouch
- 10 year extended warranty when you register your microphone
The RØDE M3 is a highly versatile end-address condenser microphone, designed to be completely at home in the studio, on stage or on location. It is equally suitable as an instrument microphone for guitars, drums and percussion or even vocals.
Featuring a heavy duty metal body and internally shock mounted 1/2" condenser capsule mounted for end-address, the M3 can be powered either via P48 phantom power, or an internal 9V battery.
A -10dB and -20dB level attenuator (pad), selectable from inside the battery compartment, allows recording of loud sound sources, such as a guitar amplifier or snare drum. A high-pass filter selectable on the microphone power switch introduces a filter at 80Hz to reduce low frequency sounds and handling noise.
The RØDE M3 microphone is designed and made in Australia, and covered by RØDE Microphones' industry leading 10 year warranty.
Specifications
| Acoustic Principle | Pressure Gradient |
| Active Electronics | JFET impedance converter with bipolar output buffer |
| Capsule | 0.50" |
| Address Type | End |
| Frequency Range | 40Hz - 20kHz(selected HPF @80Hz) |
| Output Impedance | 200Ω |
| Maximum SPL | 142dB SPL (@ 1kHz, 1% THD into 1KΩ load) |
| Maximum Output Level | 9.2mV |
| Sensitivity | -40.0dB re 1 Volt/Pascal (6.30mV @ 94 dB SPL) +/- 2 dB @ 1kHz |
| Equivalent Noise Level (A-weighted) | 21dB-A |
| Weight | 390.00gm |
|
Dimensions |
225.00mmH x 33.00mmW x 33.00mmD |
| Warranty |
1 year with free extension to 10 years following registration |
RODE M5 Compact 1/2" Condenser Microphone (Matched Pair)
$ 199.00 - Sold Out
RODE M5 Compact 1/2" Condenser Microphone (Matched Pair)
Rode SKU: M5-MP | Helix SKU: RMM5MP
Overview
Matched pair of compact 1/2" cardioid condenser microphones. Includes 2 x RM5 mic clips and 2 x WS5 windshields
- 1⁄2” capsule with gold-plated membrane
- Cardioid polar pattern
- All metal body
- Ultra-low noise
- State-of-the-art surface mount electronics
- Includes microphone clips and windshields
- 10 year extended warranty when you register your microphone
Designed and made in Australia, the M5 is a compact ½” cardioid condenser microphone with low noise and a full frequency response. A result of many years’ experience building the award-winning NT5 microphone, RØDE has succeeded in making a high-quality ‘pencil’ style permanently polarized condenser that will impress even the most demanding of artists and engineers. Ideal for studio recording and live on stage, the M5 is equally at home on a range of acoustic instruments, choirs, or anywhere you would employ a small diaphragm condenser microphone, either individually or as a stereo array. This matched pair has been carefully selected to ensure a variation of no more than 1dB sensitivity between the microphones. A premium foiled certificate is supplied to verify the authenticity of the pair. The M5 is finished with RØDE’s proprietary ceramic coating which offers a sleek matt black finish, and is supplied with WS5 windshields and RM5 stand mounts.
Specifications
| Acoustic Principle | Pressure Gradient |
| Active Electronics | JFET impedance converter with bipolar output buffer |
| Capsule | 0.50" |
| Polar Pattern | |
| Address Type | End |
| Frequency Range | 20Hz - 20kHz |
| Output Impedance | 200Ω |
| Maximum SPL | 140dB SPL (@ 1kHz, 1% THD into 1KΩ load) |
| Maximum Output Level | 13.5mV |
| Sensitivity | -34.0dB re 1 Volt/Pascal (20.00mV @ 94 dB SPL) +/- 2 dB @ 1kHz |
| Equivalent Noise Level (A-weighted) | 19dB-A |
| Power Options |
|
| Weight | 80.00gm |
| Dimensions | 100.00mmH x 20.00mmW x 20.00mmD |
| Output | |
| Warranty | 1 year with free extension to 10 years following registration |
RODE NT3 Microphone
$ 269.00 - Sold Out
RODE NT3 Microphone
Rode SKU: NT3 | Helix SKU: RMNT3
Overview
Multi-powered 3/4" cardioid condenser microphone. P48 and 9V battery powered.
- True condenser externally biased 3/4” capsule
- Dual power operation
- Cast metal body with durable satin-nickel finish
- Transformerless output
- Internal capsule shock mounting
- High level of RF rejection
- Audio-grade surface mount components
- Full frequency response
- 10 year extended warranty when you register your microphone
The NT3 is the definition of a studio workhorse. Featuring an end-address 3/4" gold-sputtered true-condenser transducer it provides incredible detail on almost any instrument you can imagine.
Intended for studio, stage and location work, this versatile handheld, stand or boompole mounted microphone will give great results on drums, percussion, acoustic guitar, guitar amps, piano and all acoustic instruments as well as detailed voice reproduction when used as a handheld presentation microphone or indoor boom mic.
For further versatility the NT3 can be powered by either P48 phantom power, or via a 9V battery for situations when power isn't available via the console or camera. Its rugged and durable all-metal body and mesh head ensure that it is well protected both in the studio and out in the field.
The RØDE NT3 microphone is designed and made in Australia, and covered by RØDE's industry leading 10 year warranty.
Specifications
| Acoustic Principle | Pressure Gradient |
| Active Electronics | JFET impedance converter with bipolar output buffer |
| Capsule | 0.75" |
| Polar Pattern | |
| Address Type | End |
| Frequency Range | 20Hz - 20kHz |
| Output Impedance | 200Ω |
| Maximum SPL | 140dB SPL (@ 1kHz, 1% THD into 1KΩ load) |
| Maximum Output Level | 9.5mV |
| Sensitivity | -39.0dB re 1 Volt/Pascal (12.00mV @ 94 dB SPL) +/- 2 dB @ 1kHz |
| Equivalent Noise Level (A-weighted) | 16dB-A |
| Power Options |
 
|
| Weight | 371.00gm |
| Dimensions | 206.00mmH x 32.00mmW x 32.00mmD |
| Output | |
| Warranty | 1 year with free extension to 10 years following registration |
RODE NT4 - Cardioid Studio Condenser X/Y Stereo Microphone
$ 529.00 - Sold Out
RODE NT4 - Cardioid Studio Condenser X/Y Stereo Microphone
Rode SKU: NT4 | Helix SKU: RMNT4
Overview
Fixed X/Y stereo 1/2" condenser microphone with 3.5mm minijack and dual XLR connectivity. P48 and 9V battery powered.
- Stereo X/Y condenser microphone
- Dual externally biased 1/2” capsules with gold sputtered diaphragm
- Capsules closely matched with full frequency response
- Dual power operation
- Custom stereo cables included - 5 pin stereo XLR, Minijack (Via included cable) and dual 3-pin XLR (via included cable)
- Custom twin head windshield (WS4) included
- Includes custom twin head windshield WS4, RC4 case and 5-pin Minijack and XLR stereo cables
- Surface mount circuitry
- 10 year extended warranty when you register your microphone
The RØDE NT4 stereo microphone offers a perfect X/Y stereo array without the need for matched pair microphones, complex stereo bars and equipment. Simply place the microphone and capture a realistic stereo field using a single microphone.
Combining an acoustically matched pair of 1/2” cardioid condenser capsules fixed in a perfect 90 degree near-coincident alignment, the NT4 instantly creates a faithful stereo array that is ideal for drum overheads, percussion, choir vocals, environmental recording and sound design in a studio or in the field.
The NT4's versatility is further extended by its ability to be powered by a 9V battery, in addition to 48V phantom power. Both stereo XLR and 3.5mm minijack cables are supplied to ensure the NT4 is ready to record to mixing console, portable recorder or camera.
The RØDE NT4 microphone is designed and made in Australia, and covered by RØDE's industry leading 10 year warranty.
Specifications
| Acoustic Principle | Pressure Gradient |
| Active Electronics | JFET impedance converter with bipolar output buffer |
| Capsule | 0.50" |
| Polar Pattern |
|
| Address Type | End |
| Frequency Range | 20Hz - 20kHz |
| Output Impedance | 200Ω |
| Maximum SPL | 143dB SPL (@ 1kHz, 1% THD into 1KΩ load) |
| Maximum Output Level | 13.9mV |
| Sensitivity | -38.0dB re 1 Volt/Pascal (12.00mV @ 94 dB SPL) +/- 2 dB @ 1kHz |
| Equivalent Noise Level (A-weighted) | 16dB-A |
| Power Options |
9V battery powered
|
| Weight | 480.00gm |
| Dimensions | 231.00mmH x 61.00mmW x 33.00mmD |
| Output |
|
| Warranty | 1 year with free extension to 10 years following registration |
RODE NT5 Cardioid Studio Condenser Microphones (Matched Pair)
$ 429.00 - Sold Out
RODE NT5 Cardioid Studio Condenser Microphones (Matched Pair)
Rode SKU: NT5 Matched Pair | Helix SKU: RMNT5MatchedPair
Overview
Pair of acoustically matched NT5 1/2" cardioid condenser microphones.
The Rode NT5 is a matched pair of small diaphragm microphones featuring full frequency response and low-noise output circuitry. Designed for general instrument recording and sound reinforcement.
The cardioid polar pattern effectively minimizes audio at the off-axis sections, reducing noise caused by, leakage, monitors, additional instruments etc. The NT5 offers a frequency response of 20 Hz to 20 kHz allowing the microphones to be used in a wide variety of applications such as drum over-head miking, stereo capturing of instruments, vocal capturing etc. The NT5 is powered via +24V or +48V phantom power. The package includes dual windscreens and stand mounts in a durable road case.
Specifications
| Operating Principle | Pressure Gradient |
| Transducer | Condenser |
| Diaphragm | 0.5" (12.70 mm) |
| Polar Pattern | Cardioid |
| Frequency Range | 20 Hz to 20 kHz |
| Signal to Noise Ratio | 78 dB |
| Equivalent Noise Level | 16 dB A-Weighted |
| Maximum SPL | 143 dB SPL 1% |
| Impedance | 100 ohms |
| Sensitivity | -38 dB, re: 1 V/Pa |
| Power Requirements | 24 V, 48 V |
| Output Connectors | 3-Pin XLR |
| Dynamic Range | 128 dB |
| Length | 4.65" (118 mm) |
| Diameter | 0.79" (20 mm) |
| Weight | 0.22 lb (100 g) |
Packaging Info:
Package Weight 3.5 lb
Box Dimensions (LxWxH) 15.6 x 12.3 x 4.4"
RODE NT5 Cardioid Studio Condenser Microphones (Single Microphone)
$ 219.00 - Sold Out
RODE NT5 Cardioid Studio Condenser Microphones (Single Microphone)
Rode SKU: NT5 | Helix SKU: RMNT5
Overview
Compact 1/2" cardioid condenser microphone.
- Externally biased condenser
- Gold sputtered 1/2” capsule
- Heavy-duty satin-nickel plated body
- Dual power operation
- Surface mount circuitry
- Low noise
- Full frequency response
- Available as Certified Match Pair
- 10 year extended warranty when you register your microphone
The NT5 is RØDE's premier small-diaphragm cardioid condenser microphone, sometimes referred to as a 'pencil mic'.
Intended for recording acoustic instruments, drum overheads, cymbals and live performances, the compact externally polarized mic employs a 1/2" capsule, an active J-FET impedance converter with bipolar output buffer.
Its tight cardioid pickup pattern also makes it ideal for use as an indoor dialogue microphone for filmmaking on a mic stand or boom.
Expanding the NT5's versatility, an interchangeable omnidirectional capsule (NT45-O) is available.
Finished in durable satin nickel, the NT5 available as a single microphone or as an acoustically matched pair.
The NT5 is designed and made in Australia, and covered by RØDE's industry leading 10 year warranty.
Specifications
| Acoustic Principle | Pressure Gradient |
| Active Electronics | JFET impedance converter with bipolar output buffer |
| Capsule | 0.50" |
| Polar Pattern | |
| Address Type | End |
| Frequency Range | 20Hz - 20kHz |
| Output Impedance | 100Ω |
| Maximum SPL | 143dB SPL (@ 1kHz, 1% THD into 1KΩ load) |
| Maximum Output Level | 13.9mV |
| Sensitivity | -38.0dB re 1 Volt/Pascal (12.00mV @ 94 dB SPL) +/- 2 dB @ 1kHz |
| Equivalent Noise Level (A-weighted) | 16dB-A |
| Power Options |
+24V phantom power required from mixer or interface
|
| Weight | 101.00gm |
| Dimensions | 118.00mmH x 20.00mmW x 20.00mmD |
| Output | |
| Warranty |
1 year with free extension to 10 years following registration |
RODE NT55 Compact Condenser Microphone (Matched Pair)
$ 829.00 - Sold Out
RODE NT55 Compact Condenser Microphone (Matched Pair)
Rode SKU: NT55 Matched Pair | Helix SKU: RMNT55MatchedPair
Overview
Pair of acoustically matched NT55 1/2" cardioid condenser microphones.
The Rode NT55 is a matched pair of compact condenser microphones designed to accurately reproduce vocals and general instruments in recording and sound reinforcement applications. The NT55 features a 3-position pad switch for added headroom while capturing loud, peaking audio signal. A 3-position low-cut filter switch eliminates low frequency noise. The NT55 is a great choice for vocals, guitar, drums, cabinets and more. The NT55 includes interchangeable omnidirectional and cardioid capsules for even further flexibility.
Interchangeable Capsules
Omnidirectional and cardioid capsules are included for added flexibility.
3-Position Pad Switch
0, -10 and -20 dB pad switch enhances headroom and minimizes distortion.
3-Position Low Frequency Roll Off
Flat, 75 Hz and 150 Hz roll-off filter switch minimizes low frequency noise.
Specifications
| Operating Principle | Pressure Gradient |
| Transducer | Condenser |
| Diaphragm | 0.5" (12.70 mm) |
| Polar Pattern | Cardioid, Omnidirectional |
| Frequency Range | 20 Hz to 20 kHz |
| Signal to Noise Ratio | 79 dB |
| Equivalent Noise Level | 15 dB A-Weighted |
| Maximum SPL | 136 dB SPL 1% |
| Impedance | 100 ohms |
| Sensitivity | -38 dB, re: 1 V/Pa |
| Power Requirements | 48 V |
| Output Connectors | 3-Pin XLR |
| Dynamic Range | 121 dB |
| Length | 5.71" (145 mm) |
| Diameter | 0.79" (20 mm) |
| Weight | 0.22 lb (100 g) |
Packaging Info
Package Weight 3.5 lb
Box Dimensions (LxWxH) 14.5 x 12.0 x 4.5"
RODE NT55 Compact Condenser Microphone (Single Microphone)
$ 369.00 - Sold Out
RODE NT55 Compact Condenser Microphone (Single Microphone)
Rode SKU: NT55 | Helix SKU: RMNT55
Overview
Compact 1/2" cardioid and omni condenser microphone.
- Externally biased condenser
- Cardioid or Omni polar pattern using included interchangable capsules
- Gold sputtered 1/2” capsule
- Three position PAD - 0dB, -10dB and -20dB
- Three position High-Pass Filter - flat, 75Hz and 150Hz
- Surface mount circuitry
- Low noise
- Available as Certified Matched Pair
- 10 year extended warranty when you register your microphone
Like the NT5, the RØDE NT55 is a small-diaphragm, true-condenser cardioid microphone, sometimes referred to as a 'pencil mic'. The NT55 adds both a three position pad (0, -10dB, -20dB) and three stage high pass filter (Off, 75Hz, 150Hz), and includes the interchangeable NT45-O omnidirectional capsule.
Intended for recording acoustic instruments, drum overheads, cymbals and live performances, the compact externally polarized mic employs a 1/2" capsule, an active J-FET impedance converter with bipolar output buffer.
Its tight cardioid pickup pattern also makes it ideal for use as an indoor dialogue microphone for filmmaking on a mic stand or boom.
Finished in durable satin nickel, the NT55 available as a single microphone or as an acoustically matched pair.
The NT55 is designed and made in Australia, and covered by RØDE's industry leading 10 year warranty.
Specifications
| Acoustic Principle | Pressure Gradient |
| Active Electronics | JFET impedance converter with bipolar output buffer |
| Capsule | 0.50" |
| Polar Pattern |
|
| Address Type | End |
| Frequency Range | 20Hz - 20kHz |
| Output Impedance | 100Ω |
| Maximum SPL | 136dB SPL (@ 1kHz, 1% THD into 1KΩ load) |
| Maximum Output Level | 8.0mV |
| Sensitivity | -38.0dB re 1 Volt/Pascal (12.60mV @ 94 dB SPL) +/- 2 dB @ 1kHz |
| Equivalent Noise Level (A-weighted) | 15dB-A |
| Power Options | |
| Weight | 110.00gm |
| Dimensions | 145.00mmH x 20.00mmW x 20.00mmD |
| Output | |
| Warranty | 1 year with free extension to 10 years following registration |
RODE NT6 Compact Condenser Microphone
$ 429.00 - Sold Out
RODE NT6 Compact Condenser Microphone
Rode SKU: NT6 | Helix SKU: RMNT6
Overview
Compact 1/2" condenser microphone with 3m (10') Kevlar® reinforced cable to detachable capsule head. Also features HPF and PAD.
- 1/2” condenser capsule with remote preamp
- Gold sputtered externally biased condenser
- Two position PAD - 0dB and -10dB
- Two position High Pass Filter - flat and 80Hz
- Includes two-axis swivel mount, 3m Kevlar® fibre reinforced cable, windshield and zip pouch
- Heavy duty satin-nickel plated body
- Low noise and full frequency response
- Designed and manufactured in Australia
- 10 year extended warranty when you register your microphone
The RØDE NT6 is an extremely compact 1/2" cardioid condenser microphone, specifically designed for difficult mounting applications where the highest quality audio is required.
Although clearly relevant to instrument miking, the NT6 is extremely well suited to any situation where an unobtrusive but powerful microphone is required such as location recording.
The microphone is split into two modular components, joined by via a custom 3m (10') shielded, Kevlar® reinforced cable.
Featuring a gold-sputtered, true-condenser capsule, the NT6 capsule head measures 45mm (1.8”) in length and weighs only 42gm (1.5oz). The included all-metal, multi-position mounting ring provides 180 degrees of vertical rotation.
The NT6 preamp-body incorporates both a high-pass filter and pad setting. The high-pass filter can be introduced to cut vibration, rumble and undesired sounds sources under 80Hz, while the PAD offers a -10dB level attenuation, useful when recording louder sound sources.
The NT6's small form factor make it an ideal small diaphragm cardioid microphone for use in the Mid-Side (M/S) stereo array, in combination with a figure-8 large diaphragm microphone such as the NT2-A, NT2000 or K2.
The NT6 is designed and made in Australia, and covered by RØDE's industry leading 10 year warranty.
Specifications
| Acoustic Principle | Pressure Gradient |
| Active Electronics | JFET impedance converter with bipolar output buffer |
| Capsule | 0.50" |
| Polar Pattern | |
| Address Type | End |
| Frequency Range | 40Hz - 20kHz |
| Output Impedance | 200Ω |
| Maximum SPL | 135dB SPL (@ 1kHz, 1% THD into 1KΩ load) |
| Maximum Output Level | 6.0mV |
| Sensitivity | -37.0dB re 1 Volt/Pascal (16.00mV @ 94 dB SPL) +/- 2 dB @ 1kHz |
| Equivalent Noise Level (A-weighted) | 19dB-A |
| Power Options |
|
| Weight | 386.00gm |
| Dimensions | 189.00mmH x 64.00mmW x 20.00mmD |
| Output | |
| Warranty | 1 year with free extension to 10 years following registration |
RODE NTG1 Condenser Shotgun Microphone
$ 249.00
RODE NTG1 Condenser Shotgun Microphone
Rode SKU: NTG1 | Helix SKU: RMNTG1
Overview
Directional super cardioid condenser shotgun microphone with switchable HPF
- Broadcast sound quality
- Low noise circuitry
- Super-cardioid polar pattern
- Condenser transducer
- Rugged metal construction
- Two step High Pass Filter (Flat/80Hz)
- Low handling noise
- Low weight - 105g (3 oz.)
- Includes mic clip, wind shield and zip case
- Ideal for professional applications within the film, video, television and production industries
- 10 year extended warranty when you register your microphone
The RØDE NTG1 is a lightweight condenser shotgun microphone, designed for professional applications within the film, video, television and production industries.
Its full frequency response, low noise and audio transparency make it an ideal film, video, and voice over microphone, while its low weight (105gm/3.7oz) makes it an ideal boom microphone.
In addition to the native 20Hz-20kHz frequency response a selectable high-pass filter at 80Hz is available, which will prevent low end noise such as air conditioners and traffic from being recorded.
The WSVM windshield is supplied to minimise light wind noise and plosives during recording. The optional 'DeadCat' furry is recommended for outdoor applications.
The RØDE NTG1 shotgun microphone is designed and made in Australia, and covered by RØDE Microphones' industry leading 10 year warranty.
Specifications
| Acoustic Principle | Line Gradient |
| Active Electronics | JFET impedance convertor with bipolar output buffer |
| Capsule | 0.50" |
| Polar Pattern | |
| Address Type | End |
| Frequency Range | 20Hz - 20kHz |
| Output Impedance | 50Ω |
| Maximum SPL | 139dB SPL (@ 1kHz, 1% THD into 1KΩ load) |
| Maximum Output Level | 6.9mV |
| Sensitivity | -36.0dB re 1 Volt/Pascal (15.00mV @ 94 dB SPL) +/- 2 dB @ 1kHz |
| Equivalent Noise Level (A-weighted) | 18dB-A |
| Power Options |
+24V phantom power required from mixer or interface
|
| Weight | 105.00gm |
| Dimensions | 219.00mmH x 22.00mmW x 22.00mmD |
| Output | |
| Warranty | 1 year with free extension to 10 years following registration |
RODE NTG3 Precision RF-Biased Shotgun Microphone - Silver
$ 699.00 - Sold Out
RODE NTG3 Precision RF-Biased Shotgun Microphone - Silver
Rode SKU: NTG3 | Helix SKU: RMNTG3
Overview
Precision broadcast-grade super cardioid shotgun mic. Withstands adverse environmental conditions. RCNTG3 storage cylinder
- Superior broadcast sound quality
- High Sensitivity
- Super-cardioid polar pattern
- Designed to withstand adverse environmental conditions
- 50% less self-noise than the majority of shotgun microphones
- Extremely low handling noise
- High level of immunity to radio frequency interference
- True Condenser (external RF biased)
- Includes durable aluminium storage cylinder for transport, pop filter, mic clip and large zip pouch
- Designed for professional use on film, television, ENG & wherever high resolution broadcast audio is required
- 10 year extended warranty when you register your microphone
The RØDE NTG3 super-cardioid shotgun microphone is designed for professional use on film, television, electronic news gathering and wherever high-resolution broadcast audio is required.
As RØDE's premier directional microphone the NTG3 exhibits superlative audio quality with a rich, warm quality and a full frequency response. Its RF bias technology makes it almost completely resistant to moisture, making it the only option when recording in demanding environments where condensation is an issue.
Machined from solid brass and available in either anti-glare, nickel-plated finish or matte black (NTG3B), the NTG3 is incredibly robust while remaining light weight.
Its precise yet forgiving polar pattern ensures that whether used on-camera or on a boom pole, the NTG3 will capture audio clearly every time.
A durable aluminum storage cylinder is supplied to provide the ultimate protection for the NTG3 while in storage and transport. Tightly sealed at both ends the cylinder is highly weatherproof, adding to the microphone's rugged performance credentials.
The RØDE NTG3 shotgun microphone is designed and made in Australia, and covered by RØDE Microphones' industry leading 10 year warranty.
Specifications
| Acoustic Principle | Line Gradient |
| Active Electronics | RF Bias |
| Capsule | 0.50" |
| Polar Pattern | |
| Address Type | End |
| Frequency Range | 40Hz - 20kHz |
| Output Impedance | 25Ω |
| Maximum SPL | 130dB SPL (@ 1kHz, 1% THD into 1KΩ load) |
| Maximum Output Level | 8.2mV |
| Sensitivity | -30.0dB re 1 Volt/Pascal (31.60mV @ 94 dB SPL) +/- 2 dB @ 1kHz |
| Equivalent Noise Level (A-weighted) | 13dB-A |
| Power Options | |
| Weight | 163.00gm |
| Dimensions | 255.00mmH x 19.00mmW x 19.00mmD |
| Output |
3-pin XLR Output
|
| Warranty | 1 year with free extension to 10 years following registration |
RODE NTK Valve 1.0" Condenser Microphone
$ 529.00 - Sold Out
RODE NTK Valve 1.0" Condenser Microphone
Rode SKU: NTK | Helix SKU: RMNTK
Overview
Versatile class A valve 1" cardioid condenser microphone
- Large 1” capsule with gold plated diaphragm
- Class “A” valve circuitry
- Hand selected and graded 6922 twin-triode valve
- Dedicated power supply
- Internal capsule shock mounting
- High level of RF rejection
- Ultra low noise
- Wide dynamic range
- High strength heat treated steel mesh head
- 10 year extended warranty when you register your microphone
Like it’s bigger brother the K2, the RØDE NTK is a premium valve condenser microphone designed to provide incredible detail and warmth in the studio. Its cardioid polar pattern is perfect for most single instrument recording scenarios.
The electronic circuitry complementing this very sensitive transducer includes a hand-selected twin-triode 6922 valve and audiophile grade components. The result is an ultra-wide dynamic range, low noise, and stunning tube warmth. The NTK's rich valve sound is ideal for vocals, acoustic instruments, drum overheads, guitar amps and pianos.
The RØDE NTK microphone is designed and made in Australia, and covered by RØDE Microphones' industry leading 10 year warranty.
Specifications
| Acoustic Principle | Pressure Gradient |
| Active Electronics | Valve/tube impedance converter with bipolar output buffer |
| Capsule | 1.00" |
| Polar Pattern |
Cardioid - Picks up audio from the front and sides and rejects from the rear
|
| Address Type | Side |
| Frequency Range | 20Hz - 20kHz |
| Output Impedance | 200Ω |
| Maximum SPL | 158dB SPL (@ 1kHz, 1% THD into 1KΩ load) |
| Maximum Output Level | 29.0mV |
| Sensitivity | -38.0dB re 1 Volt/Pascal (25.00mV @ 94 dB SPL) +/- 2 dB @ 1kHz |
| Equivalent Noise Level (A-weighted) | 12dB-A |
| Power Options |  |
| Weight | 760.00gm |
| Dimensions | 208.00mmH x 55.00mmW x 55.00mmD |
| Output | |
| Warranty | 1 year with free extension to 10 years following registration |
RODE NTR Active Ribbon Microphone
$ 799.00 - Sold Out
RODE NTR Active Ribbon Microphone
Rode SKU: NTR | Helix SKU: RMNTR
Overview
NTR Active Ribbon Microphone
- Highly sensitive 1.8 micron ribbon element
- Bi-Directional Polar Pattern
- Internal Shock Mounting System
- Custom designed and manufactured transformer
- Heavy-duty matte black finish
- Ribbon-securing travel screw supplied
- Designed and manufactured in Australia
- One free ribbon replacement during warranty period
- 10 year extended warranty when you register your microphone
At first glance of the NTR you’re aware that it’s very special and unique – an intricate blend of art and science.
Designed to hang in the world’s finest recording studios and performance halls equally as well as home studio spaces, its existence is a labour of love for RØDE. Every element of the NTR, from the transformer to the ribbon element itself, has been designed and created in-house at RØDE’s headquarters in Sydney, Australia. All with the aim of crafting the finest ribbon microphone available.
Sonically, the NTR is capable of reproducing unprecedented high frequency detail and accuracy, addressing common criticisms of other ribbon microphones, while opening up the possible usage scenarios considerably. This allows it to record sound sources that usually require a more sensitive microphone element.
Specifications
| Acoustic Principle | Velocity Transducer |
| Active Electronics | Step-up Transformer and signal balanced preamp stage |
| Polar Pattern |
Figure 8 - picks up from the front and rear and rejects sides
|
| Address Type | Side |
| Frequency Range | 20Hz - 20kHz |
| Output Impedance | 200Ω |
| Maximum SPL | 130dB SPL (@ 1kHz, 1% THD into 1KΩ load) |
| Sensitivity | -30.5dB re 1 Volt/Pascal (30.00mV @ 94 dB SPL) +/- 2 dB @ 1kHz |
| Equivalent Noise Level (A-weighted) | 15dB-A |
| Power Options | |
| Weight | 1047gm |
| Dimensions | 216mmH x 65mmW x 65mmD |
| Output | |
| Warranty | 1 year with free extension to 10 years following registration |
RODE Omnidirectional Lavalier Microphone
$ 249.00
RODE Omnidirectional Lavalier Microphone
Rode SKU: Lavalier | Helix SKU: RMLavalier
Overview
The RØDE Lavalier is a discreet lapel microphone that provides broadcast-quality audio when close-miked in almost any scenario.
The Lavalier's low self-noise, user friendly omni-directional polar pattern and minimal appearance make it an ideal solution for film, television, video, theatre, house of worship and anywhere where a high quality microphone needs to be heard but not seen.
The microphone capsule is connected via a 1.2m (4') shielded, detachable Kevlar® reinforced cable that has been rigorously strain tested up to 10kg to ensure reliable performance.
The included mini-furry for high wind protection ensures quality recordings in adverse environments, and the included cable management clips ensure that you are able to minimise the microphone and cable visibility, while providing maximum mobility for the wearer.
The supplied anti-trauma water resistant case provides rugged and secure protection for the microphone, cable, clips and included accessories.
Knowing that versatility is paramount in any product, RØDE has developed the MiCon™ connector system which provides seamless integration between the Lavalier and a wide range of wireless systems as well as consoles, cameras and portable recorders.
The RØDE Lavalier lapel microphone is designed and made in Australia and is covered by RØDE Microphones' innovative 5 year 'no questions asked' warranty which provides 12 months of complete cover, and an optional US$99 replacement microphone during the extended warranty period.
Specifications
| Acoustic Principle | Pressure Gradient |
| Active Electronics | JFET impedance converter |
| Capsule | 0.10" |
| Address Type | End |
| Frequency Range | 60Hz - 18kHz |
| Output Impedance | 3000Ω |
| Maximum SPL | 110dB SPL (@ 1kHz, 1% THD into 1KΩ load) |
| Maximum Output Level | 189.0mV |
| Sensitivity | -33.5dB re 1 Volt/Pascal (21.00mV @ 94 dB SPL) +/- 2 dB @ 1kHz |
| Equivalent Noise Level (A-weighted) | 25dB-A |
| Weight | 1.00gm |
| Dimensions | 12.00mmH x 4.50mmW x 4.50mmD |
| Warranty | 1 year with free extension to 5 years following registration |
IN THE BOX:
Rode PG1 Cold Shoe Pistol Grip
$ 29.95 - Sold Out
Rode PG1 Cold Shoe Mount for Shotgun Mics
The Rode PG1 Cold Shoe Mount for Shotgun Mics is a convenient and ergonomic way to operate your video microphone indepently of your video camera. The Rode PG1 Pistol Grip Cold Shoe Mount is an ideal solution for the Rode VideoMic, Stereo VideoMic and other cold-shoe mounted shotgun and stereo microphones. The built-in cold shoe mount makes a secure connection between the microphone and the grip. For even more versatility, the PG1 features a 3/8-inch thread on the base that allows connection to a boompole or microphone stand, while the spine features handy cable management. Don't miss out on this handy accessory, own yours today!
- An excellent accessory for audio video applications
- For using Rode VideoMics and other cold shoe mics independent of the camera
- Cold shoe mount provides a secure connection between the mic and grip
- 3/8-inch thread on for connection to a boompole or mic stand
- Spine design offers handy cable management
RODE PinMic-Long Wearable Microphone
$ 249.00 - Sold Out
RODE PinMic-Long Wearable Microphone
Rode SKU: PinMic-Long | Helix SKU: RMPinMicLong
Overview
Unique lapel style 'pin-through' microphone that attaches to clothing and fabric almost anywhere. Long pin version.
- Intuitive And Subtle
- Omni-directional polar pattern
- Removable Mesh Head
- Ultra Discreet Appearance
- Lightweight And Easy To Position
- High Quality Performance
- Low Noise Miniature Microphone Capsule
- Low Handling Noise
- Universal Compatibility
- RØDE Micon interconnectivity system provides seamless integration with a wide range of wireless systems
- Includes mini-furry, anti-trauma case, spare capsule and PinMic tool kit
- Five year extended warranty when you register your microphone
The RØDE PinMic™ is a discreet lavalier/lapel microphone with an innovative pin-through design that is not only easier to conceal than a traditional lapel microphone, but provides greater mounting versatility.
Comprised of a cabled backplate and a removable omni-directional capsule head, the PinMic™ is easily mounted onto any clothing or fabric by simply pushing the backplate pins through the back of the fabric and sliding the capsule into place on the front. The microphone backplate and cable are hidden behind the fabric, and the capsule head can be easily disguised, covered or decorated to further conceal the microphone.
The PinMic™ capsule is discrete at only 9mm deep and 11mm in diameter, and is supplied with both a black and an unpainted silver mesh head that can be further camouflaged by painting.
The microphone easily mounts through any fabric up to 1.5mm (0.006") thick without any damage to clothing. A longer pin version (PinMic-Long) is available for mounting on thicker fabrics (up to 3.5mm/0.14" thick).
The microphone capsule is connected via a 1.2m (4') shielded, detachable Kevlar® reinforced cable that has been rigorously strain tested to ensure reliable performance.
The included mini-furry for high wind protection ensures quality recordings in adverse environments, while the anti-trauma water resistant case provides rugged and secure protection for the microphone, a spare capsule head, the microphone cable and included accessories.
The PinMic™ is an ideal solution for film, television, video, theatre, house of worship and anywhere where a high quality microphone needs to be heard but not seen.
Knowing that versatility is paramount in any product, RØDE has developed the MiCon™ connector system which provides seamless integration between the PinMic™ and a wide range of wireless systems as well as consoles, cameras and portable recorders.
The RØDE PinMic™ lapel microphone is designed and made in Australia and is covered by RØDE Microphones' innovative 5 year 'no questions asked' warranty which provides 12 months of complete cover, and an optional US$99 replacement microphone during the extended warranty period.
Specifications
| Acoustic Principle |
Pressure Gradient |
|
Active Electronics |
JFET impedance converter |
| Capsule | 0.10" |
| Polar Pattern | |
| Address Type | End |
| Frequency Range | 60Hz - 18kHz |
| Output Impedance | 3000Ω |
| Maximum SPL | 110dB SPL (@ 1kHz, 1% THD into 1KΩ load) |
| Maximum Output Level | 189.0mV |
| Sensitivity | -33.5dB re 1 Volt/Pascal (21.00mV @ 94 dB SPL) +/- 2 dB @ 1kHz |
| Equivalent Noise Level (A-weighted) | 25dB-A |
| Power Options |
+48V phantom power required from mixer or interface
|
| Weight | 10.00gm |
| Dimensions | 16.00mmH x 22.00mmW x 33.00mmD |
| Output | |
| Warranty | 1 year with free extension to 5 years following registration |
RODE Podcaster USB Broadcast Microphone
$ 229.00
RODE Podcaster USB Broadcast Microphone
Rode SKU: Podcaster | Helix SKU: RMPodcaster
Overview
The RØDE Podcaster is a dynamic, end-address USB microphone that combines broadcast-quality audio with the simplicity of USB connectivity, allowing recording direct to a computer without the need for an additional digital interface.
Including an audiophile quality 18-bit resolution, 48kHz sampling A/D converter, the Podcaster processes all of the analogue-to-digital conversion internally, bypassing the computer's lower quality on-board sound controller altogether.
A headphone output on the microphone body provides zero-latency monitoring, so the user can hear exactly what is being recorded, free of delay or echo.
The Podcaster features an internal pop filter, designed to minimise plosives sounds that can overload the microphone capsule and distort the audio output.
It is fully compatible with Windows 7, Windows 8 and Mac OS X computers, as well as several Linux distributions. The microphone is bus powered and features a status LED to indicate operation.
The Podcaster is ideal for podcasting, vodcasting, YouTube videos, voice recognition software, corporate videos and any production application that requires a simple yet professional voice-over microphone. It is also a convenient demo microphone for musicians and songwriters that prefer the convenience of a USB microphone but don't want to compromise sound quality.
It can also be used as an iPad microphone for the Apple iPad (in conjunction with the iPad Camera Connection Kit and a powered USB hub) to provide high quality recording to various iPad audio applications such as Garageband.
The Podcaster includes a sturdy RM2 microphone ring mount. For professional applications the optional PSM1 shock mount and PSA1 boom arm are highly recommended.
The RØDE Podcaster USB microphone is designed and made in Australia, and covered by RØDE Microphones' industry leading 10 year warranty.
- Broadcast Sound Quality
- 28mm dynamic capsule
- 18-bit resolution, 8-48kHz sampling
- Windows and Mac compatible
- Powered by USB bus
- Internal capsule shock mounting
- 3.5mm stereo headphone output with volume control built-in to body
- Ideal for voice recognition software
- 10 year extended warranty when you register your microphone
Specifications
| Acoustic Principle | Dynamic |
| Active Electronics | Analogue signal conditioning + A/D and USB interface |
| Polar Pattern | |
| Resolution | 18-bit |
| Sampling Rate | 8-48kHz |
| Address Type | End |
| Frequency Range | 40Hz - 14kHz |
| Output Impedance | 0Ω |
| Maximum SPL | 115dBSPL |
| Sensitivity | -51.0dB re 1 Volt/Pascal (2.80mV @ 94 dB SPL) +/- 2 dB @ 1kHz |
| Power Options |  |
| Weight | 655.00g |
| Dimensions | 215.00mmH x 56.00mmW x 52.00mmD |
| Output | |
| Warranty | 1 year with free extension to 10 years following registration |
RODE Procaster Broadcast Quality Dynamic Microphone
$ 229.00
RODE Procaster Broadcast Quality Dynamic Microphone
Rode SKU: Procaster | Helix SKU: RMProcaster
Overview
Broadcast quality cardioid end-address dynamic microphone
- Broadcast quality sound
- High output dynamic capsule
- Balanced, low impedance output
- Internal shock mounting of capsule for low handling noise
- Internal pop-filter to reduce plosives
- Robust, all-metal construction
- 10 year extended warranty when you register your microphone
The RØDE Procaster is a professional broadcast quality dynamic microphone, specifically designed to offer no-compromise performance for voice applications in the broadcast environment.
Featuring a tight polar pattern and tailored-for-voice frequency response, the Procaster is perfect for every application where a great sounding, robust microphone with superior ambient noise rejection is demanded.
The Procaster features an internal pop filter, designed to minimise plosives sounds that can overload the microphone capsule and distort the audio output.
Its high output dynamic capsule and balanced low impedance output make it an ideal broadcast and voice over microphone.
The RØDE Procaster microphone is designed and made in Australia, and covered by RØDE Microphones' industry leading 10 year warranty.
Specifications
| Acoustic Principle | Dynamic |
| Polar Pattern | |
| Address Type | End |
| Frequency Range | 75Hz - 18kHz |
| Output Impedance | 320Ω |
| Sensitivity | -56.0dB re 1 Volt/Pascal (1.60mV @ 94 dB SPL) +/- 2 dB @ 1kHz |
| Weight | 745.00gm |
| Dimensions | 214.00mmH x 53.00mmW x 53.00mmD |
| Output | |
| Warranty | 1 year with free extension to 10 years following registration |
RODE Reporter Omnidirectional Handheld Interview Microphone
$ 129.00 - Sold Out
RODE Reporter Omnidirectional Handheld Interview Microphone
Rode SKU: Reporter | Helix SKU: RMReporter
Overview
- Omnidirectional polar pattern
- Broadcast recording presentation and interview microphone
- “Tailored for voice” frequency response
- Ergonomic die-cast body
- Multi-layer mesh basket for wind protection
- Includes detachable microphone flag and zip case
- 10 year extended warranty when you register your microphone
Designed for handheld interview and presentation applications, the Reporter features an omnidirectional dynamic capsule that is designed to allow the user freedom of use, without the technique related issues typical of directional end-address microphones.
Additionally its frequency response has been specially tailored for voice reproduction, to maximise intelligibility and deliver crisp, clear results in almost any condition.
The microphone features a durable die-cast aluminium alloy body coated in a discrete matte black anti-glare finish. An innovative multi-layer mesh basket protects the microphone from environmental noise without the need for a bulky and distracting foam wind shield.
It is supplied with a removable microphone ‘flag’ that can accommodate high-visibility branding.
The RØDE Reporter microphone is designed in Australia and covered by RØDE Microphones' industry leading 10 year warranty.
Specifications
| Acoustic Principle | Dynamic |
| Polar Pattern | |
| Address Type | End |
| Frequency Range | 70Hz - 15kHz |
| Output Impedance | 150Ω |
| Sensitivity | -56.0dB re 1 Volt/Pascal (1.00mV @ 94 dB SPL) +/- 2 dB @ 1kHz |
| Weight | 256.00gm |
| Dimensions | 272.50mmH x 41.50mmW x 41.50mmD |
| Output | |
| Warranty | 1 year with free extension to 10 years following registration |
RODE RM5 Stand Mount for the NT5 Microphone
$ 14.99 - Sold Out
RODE RM5 Stand Mount for the NT5 Microphone
- Externally biased condenser
- Gold sputtered 1/2” capsule
- Heavy-duty satin-nickel plated body
- Dual power operation
- Surface mount circuitry
- Low noise
- Full frequency response
- Available as Certified Match Pair
- 10 year extended warranty when you register your microphone
The NT5 is RØDE's premier small-diaphragm cardioid condenser microphone, sometimes referred to as a 'pencil mic'.
Intended for recording acoustic instruments, drum overheads, cymbals and live performances, the compact externally polarized mic employs a 1/2" capsule, an active J-FET impedance converter with bipolar output buffer.
Its tight cardioid pickup pattern also makes it ideal for use as an indoor dialogue microphone for filmmaking on a mic stand or boom.
Expanding the NT5's versatility, an interchangeable omnidirectional capsule (NT45-O) is available.
Finished in durable satin nickel, the NT5 available as a single microphone or as an acoustically matched pair.
The NT5 is designed and made in Australia, and covered by RØDE's industry leading 10 year warranty.
| Acoustic Principle | Pressure Gradient |
| Active Electronics | JFET impedance converter with bipolar output buffer |
| Capsule | 0.50" |
| Polar Pattern | |
| Address Type | End |
| Frequency Range | 20Hz - 20kHz |
| Output Impedance | 100Ω |
| Maximum SPL | 143dB SPL (@ 1kHz, 1% THD into 1KΩ load) |
| Maximum Output Level | 13.9mV |
| Sensitivity | -38.0dB re 1 Volt/Pascal (12.00mV @ 94 dB SPL) +/- 2 dB @ 1kHz |
| Equivalent Noise Level (A-weighted) | 16dB-A |
| Power Options |
|
| Weight | 101.00gm |
| Dimensions | 118.00mmH x 20.00mmW x 20.00mmD |
| Output | |
| Warranty | 1 year with free extension to 10 years following registration |
Rode SM4-R Rycote Lyre Shock Mount
$ 49.00 - Sold Out
RØDE SM4-R Rycote Lyre Shock Mount
RØDE SKU: SM4-R | Helix SKU: RMSM4R
Overview
The SM4-R is a suspension shock mount for mounting various RØDE microphones onto a mic stand or boompole with 3/8" or 5/8" thread.
The SM4-R is equipped with dual Rycote Lyre mounts to ensure maximum isolation from any handling vibrations, four possible mounting points to suit the complete range of compatible RØDE shotgun microphones, and integrated cable management clip.
The stand mount is angle adjustable and can be locked into position to ensure sturdy and reliable mic positioning.
Specifications
| Weight | 110g |
| Dimensions | 110mmH x 35mmW x 117mmD |
| Warranty | 1 year |
RODE smartLav+ Lavalier Condenser Microphone for Smartphones
$ 79.00 - Sold Out
RODE smartLav+ Lavalier Condenser Microphone for Smartphones
Rode SKU: amart Lav+ | Helix SKU: RMsmartLavP
Overview
- Broadcast quality, professional-grade Lavalier Mic with TRRS Jack
- High-quality omni-directional condenser capsule
- Discrete 4.5mm miniature microphone
- Compatible with iOS devices and select Android devices*
- Kevlar® reinforced cable
- Includes wind shield and durable mounting clip
- Twelve month warranty
The smartLav+ is a broadcast-grade wearable microphone designed for use in a wide range of film, television and broadcast scenarios, or wherever broadcast quality audio is required in a discreet, portable format without the complication and expense of additional wireless equipment.
With the smartLav+ the user simply mounts the microphone on the talent, connects it to a smartphone or tablet headset jack and records via the RØDE Rec app for iOS, or any other audio app of their choice.
By employing a professional quality omni-directional condenser capsule the smartLav+ picks up sound equally from all around the microphone, allowing for versatility when mounting and ensuring a high degree of user-friendly operation.
A foam pop shield is supplied to minimise wind noise and vocal plosives (hard ‘b’, ‘t’ and ‘p’ sounds), as well as a durable mounting clip with in-built cable management. Its Kevlar® reinforced cable ensures that you never stretch or snap your microphone under normal usage conditions.
The smartLav+ is compatible with any audio app that accepts input from the headset connection, however it has been designed to pair perfectly with RØDE’s RØDE Rec app for Apple iOS devices. RØDE Rec turns the user’s iOS device into a fully-featured field recorder, with a wide range of equalisation presets to suit various recording situations, in addition to professional editing functions and the ability to publish to SoundCloud and Dropbox direct from the app.
Specifications
| Acoustic Principle | Permanently Polarise |
| Active Electronics | JFET |
| Capsule | 0.10" |
| Polar Pattern | |
| Address Type | End |
| Frequency Range | 60Hz - 18kHz |
| Output Impedance | 3Ω |
| Maximum SPL | 110dB SPL (@ 1kHz, 1% THD into 1KΩ load) |
| Maximum Output Level | 189.0mV |
| Sensitivity | -35.0dB re 1 Volt/Pascal (17.80mV @ 94 dB SPL) +/- 2 dB @ 1kHz |
| Equivalent Noise Level (A-weighted) | 27dB-A |
| Weight | 6.00gm |
| Dimensions | 1180.00mmH x 4.50mmW x 4.50mmD |
| Output | |
| Warranty | 1 year |
What's in the Box
|
smartLav+ Lavalier microphone for smartphones |
 |
LAV-CLIP Microphone Mounting Clip |
 |
WS-LAV Pop Filter/Wind Shield |
RODE Stereo VideoMic Camera-Mounted Stereo Microphone
$ 249.00 - Sold Out
RODE Stereo VideoMic Camera-Mounted Stereo Microphone
Rode SKU: Stereo VideoMic | Helix SKU: RMStereoVideoMic
Overview
The RØDE Stereo VideoMic is a high-quality stereo microphone designed for use with camcorders, DSLR cameras and portable audio recorders.
Two high-resolution 1/2" condenser capsules are mounted in a fixed X/Y stereo array, providing a very natural stereo recording, while still offering a high level of rear rejection.
The Stereo VideoMic is an ideal microphone for capturing environmental and ambient sounds, as well as live music. For dialogue and directional applications the RØDE VideoMic and VideoMic Pro are recommended.
An in-built shock mounting system isolates the Stereo VideoMic capsule and electronics from its mount, providing isolation from external physical factors that may cause unwanted rumble and vibrations in the microphone.
Its standard sized shoe mount also includes a 3/8" thread in the base for easy mounting on a boom pole or stand.
In addition to the microphone's native 40Hz-20kHz response a selectable high-pass filter at 80Hz is available, which will prevent low end noise such as air conditioners and traffic from being recorded.
A -10dB level attenuation (or PAD), selectable from the rear face of the microphone, allows recording of loud sound sources, such as live music or motorsport.
The RØDE Stereo VideoMic stereo on-camera microphone is designed in Australia and covered by RØDE Microphones' industry leading 10 year warranty.
Specifications
| Acoustic Principle | Pressure Gradient |
| Active Electronics | JFET impedance converter |
| Capsule | 0.50" |
| Polar Pattern |
Paired cardioid capsules in X-Y stereo pattern
|
| Address Type | End |
| Frequency Range | 40Hz - 20kHz |
| Output Impedance | 200Ω |
| Maximum SPL | 134dB SPL (@ 1kHz, 1% THD into 1KΩ load) |
| Sensitivity | -38.0dB re 1 Volt/Pascal (12.60mV @ 94 dB SPL) +/- 2 dB @ 1kHz |
| Equivalent Noise Level (A-weighted) | 20dB-A |
| Power Options | |
| Weight | 288.00gm |
| Dimensions | 65.00mmH x 102.00mmW x 170.00mmD |
| Output | |
| Warranty | 1 year with free extension to 10 years following registration |
Rode VideoMic Directional Video Condenser Microphone w/Mount
$ 149.00 - Sold Out
The RODE VideoMic Direction Video Condenser Microphone is a professional-grade shotgun microphone. Based on the latest Film industry technology, the VideoMic is designed specifically for use with high quality digital video cameras. The microphone exhibits low noise and an unusually wide bandwidth for its size. It is ultra lightweight, yet rugged due to it's ABS construction. The VideoMic is powered by a standard 9 V battery and offers a low battery LED status indicator and a switchable high pass filter to reduce unwanted low frequency rumble. The VideoMic attaches to any camcorder that has the standard camera-shoe fitting and utilizes a stereo mini jack for audio output. RODE VideoMic Shotgun Microphone Features Broadcast and studio sound quality Rugged reinforced ABS construction two step high-pass filter - flat or 80 Hz integrated shock mount 9 V battery operation condenser transducer low noise circuitry low handling noise includes windscreen integrated camera-shoe mount
Rode Vlogger Kit - iOS Edition for iOS devices
$ 149.00 - Sold Out
Rode Vlogger Kit - iOS Edition for iOS devices
Rode SKU: VLOGVMML | Helix SKU: RMVLOGVMML
Overview
The iOS Vlogger Kit contains everything you need to get professional results when filming using your iPhone. The VideoMic Me-L microphone connects directly to your device, delivering crisp, clear, directional sound for any application. The SmartGrip secures your device firmly in place for stable recording and connects seamlessly to the Tripod 2 for either handheld or tabletop use, while the MicroLED ensures all your shots are perfectly lit.
Key Features:
- Complete iPhone filmmaking kit
- Directional sound pickup to reduce background noise
- MicroLED light offers over four hours operation on a single charge
- Three-position tripod for handheld or static use
- Gimbal tripod head for accurate camera positioning
- All-metal mount with rubberised grips for phones 65mm to 85mm wide
- All-in-one mobile filmmaking kit, including a RØDE VideoMic, Tripod 2, SmartGrip, MicroLED and accessories
- Options for iOS (Lightning), Android (USB-C) devices and a Universal Edition (3.5mm)
- High-quality microphone that delivers professional sound in any recording situation
- Three-position tripod for either handheld or tabletop use
- MicroLED on-camera light with eight coloured filters for flawless shots
- Lightweight all-metal mount with rubberised grips, accommodates phones 65mm to 85mm wide
IN THE BOX:
- VideoMic Me-C Microphone
- Rubber Clip
- WS9 Windshield
- SmartGrip
- Tripod 2
- MicroLED On-camera Light
- Clip-on Diffuser
- 8 Coloured Filters
- USB-C Cable for recharging the MicroLED on-camera light
Rode Vlogger Kit - USB-C Edition for compatible phones
$ 149.00 - Sold Out
Rode Vlogger Kit - USB-C Edition for compatible phones
Rode SKU: VLOGVMMC | Helix SKU: RMVLOGVMMC
Overview
The USB-C Vlogger Kit contains everything you need to get professional results when filming using your USB-C equipped mobile phone. The VideoMic Me-C microphone connects directly to your device, delivering crisp, clear, directional sound for any application. The SmartGrip secures your device firmly in place for stable recording and connects seamlessly to the Tripod 2 for either handheld or tabletop use, while the MicroLED ensures all your shots are perfectly lit.
Key Features:
- Complete USB-C mobile fi lmmaking kit
- Directional sound pickup to reduce background noise
- MicroLED light offers over four hours operation on a single charge
- Three-position tripod for handheld or static use
- Gimbal tripod head for accurate camera positioning
- All-in-one mobile filmmaking kit, including a RØDE VideoMic, Tripod 2, SmartGrip, MicroLED and accessories
- Options for iOS (Lightning), Android (USB-C) devices and a Universal Edition (3.5mm)
- High-quality microphone that delivers professional sound in any recording situation
- Three-position tripod for either handheld or tabletop use
- MicroLED on-camera light with eight coloured filters for flawless shots
- Lightweight all-metal mount with rubberised grips, accommodates phones 65mm to 85mm wide
|
IN THE BOX
|
Rode VXLR Adapter for VideoMic Mini-Jack Female to XLR Male
$ 12.99 - Sold Out
RODE VXLR Minijack to XLR Adaptor
The RODE VXLR Minijack to XLR Adaptor is used to convert a 3.5 mm minijack to a 3 pin XLR. Use the VXLR adaptor to hook your Video Mic up to your studio gear. It's that simple!
Weight:
48.00gm
Dimensions:
58.00mmH x 19.00mmW x 19.00mmD
RØDE K2 - Variable Pattern Studio Tube Condenser Microphone
$ 699.00
RØDE K2 - Variable Pattern Studio Tube Condenser Microphone
RØDE SKU: K2 | Helix SKU: RMK2
Overview
Seamlessly variable dual 1" condenser valve microphone featuring continually variable polar pattern (omni through cardioid to figure 8).
- Large 1" capsule with gold sputtered diaphragm and internal shock mounting
- Ultra low noise
- Wide dynamic range
- Class ‘A’ valve circuitry
- Hand-selected and graded 6922 twin-triode valve
- Dedicated Power Supply
- High strength welded and heat-treated steel mesh head
- Continuously variable polar patterns. From omni, through cardioid to figure 8, controlled at the power supply.
- 10 year extended warranty when you register your microphone
The RØDE K2 is a premium valve condenser microphone featuring dual 1” gold sputtered diaphragms. Infinitely variable control of the polar pattern from omnidirectional through cardioid and bidirectional/figure-8 provides the freedom and flexibility to excel in any recording situation.
High-performance specifications (including a maximum SPL of 162dB) are combined with the character and subtleties of the legendary mics of the 1950s to provide a microphone that not only provides world-class vocals but is perfectly at home recording a wide range of instruments both up-close or in a wider ‘room’ capacity.
The RØDE K2 microphone is designed and made in Australia, and covered by RØDE Microphones' industry leading 10 year warranty.
Specifications
| Acoustic Principle | Pressure Gradient |
| Active Electronics | Valve/tube impedance converter with bipolar output buffer |
| Capsule | 1.00" |
| Polar Pattern |
|
| Address Type | Side |
| Frequency Range | 20Hz - 20kHz |
| Output Impedance | 200Ω |
| Maximum SPL | 162dB SPL (@ 1kHz, 1% THD into 1KΩ load) |
| Maximum Output Level | 30.0mV |
| Sensitivity | -36.0dB re 1 Volt/Pascal (16.00mV @ 94 dB SPL) +/- 2 dB @ 1kHz |
| Equivalent Noise Level (A-weighted) | 10dB-A |
| Power Options | |
| Weight | 815.00gm |
| Dimensions | 208.00mmH x 55.00mmW x 55.00mmD |
| Output | |
| Warranty | 1 year with free extension to 10 years following registration |
RØDE NT1 Condenser Microphone Cardioid
$ 249.00 - Sold Out
RØDE NT1 Condenser Microphone Cardioid
RØDE SKU: NT1 | Helix SKU: RMNT1
Overview
- Large 1" condenser capsule with gold-plated membrane
- Cardioid polar pattern
- Internal Rycote® Lyre® based capsule shock mounting system
- Ultra-low noise, self noise of only 4.5dB (A)
- State-of-the-art surface mount electronics
- Available with included RM2 mount (NT1-SINGLE) or with SMR shock mount (NT1-KIT)
- 10 year extended warranty when you register your microphone
The NT1 is a revolutionary new 1" diaphragm condenser microphone from RØDE.
Although the body of the new NT1 closely resembles the NT1-A, the microphone has been completely redesigned from the ground up, with the only shared component being the mesh grille.
RØDE’s design engineers approached the NT1 as a marriage of innovation and tradition, starting with the capsule which is a completely new design. Codenamed the HF6, it is the perfect example of RØDE’s fusion of artistic design approaches and cutting-edge manufacturing techniques, and features a sound signature reminiscent of the famous microphones of old while at the same time exhibiting extremely low noise.
It has been developed with a focus on detailed midrange response, coupled with silky smooth high frequencies, and warm, round, bass reproduction to make the NT1 an absolute standout in its class.
In another world-first for RØDE, the transducer itself is suspended inside the microphone using Rycote’s industry-leading Lyre system, minimizing external vibrations at the capsule level. The capsule is then married to high-grade electronics that have been designed to provide the lowest noise level of any studio microphone available. The NT1 is an incredibly quiet microphone, measuring only 4.5dBA of self-noise.
Its body is machined from 6061 aluminium and then nickel plated for resistance against corrosion. Finally it is coated in a durable, military-grade ceramic layer, using advanced electrostatic application techniques developed by RØDE to ensure an extremely hard wearing finish that is resistant to scratches or marks.
The NT1 is supplied with the revolutionary new RØDE SMR shock mount. Featuring a unique double-Lyre suspension system, the SMR enhances the existing superior vibration cancellation of Rycote’s Lyre system by using a smaller inner Lyre to act as a tensioning element. This maintains each Lyre in the neutral position where it is most efficient at cancelling vibration. The SMR’s removable all-metal pop filter is as effective as it is visually striking, providing an integrated solution for plosive protection that is easily washable and designed to last as long as the shock mount and microphone.
The NT1 is designed and made in Australia, and is covered by RØDE's industry-leading 10 year warranty.
NT1 Specifications:
| Acoustic Principle | Pressure Gradient |
| Active Electronics | JFET impedance converter with bipolar output buffer |
| Capsule | 1.00" |
| Polar Pattern | |
| Address Type | Side |
| Frequency Range | 20Hz - 20kHz |
| Output Impedance | 100Ω |
| Maximum SPL | 132dB SPL (@ 1kHz, 1% THD into 1KΩ load) |
| Maximum Output Level | 8.0mV |
| Sensitivity | -29.0dB re 1 Volt/Pascal (35.00mV @ 94 dB SPL) +/- 2 dB @ 1kHz |
| Equivalent Noise Level (A-weighted) | 4dB-A |
| Power Options |
|
| Weight | 440.00gm |
| Dimensions | 187.00mmH x 50.00mmW x 50.00mmD |
| Output | |
| Warranty | 1 year with free extension to 10 years following registration |
RØDE NT1-A Cardioid Large-Diaphragm Condenser Microphone
$ 229.00 - Sold Out
RØDE NT1-A Cardioid Large-Diaphragm Condenser Microphone
RØDE SKU: NT1-A | Helix SKU: RMNT1A
Overview
Incredibly quiet 1" cardioid condenser microphone
- Large 1” capsule with gold plated diaphragm
- Cardioid polar pattern
- Ultra low noise, self noise of only 5dB (A)
- Wide dynamic range
- True condenser (externally biased)
- Internal capsule shock mounting
- Includes RØDE SM6 shock mount, pop filter and dust cover
- 10 year extended warranty when you register your microphone
The RØDE NT1-A 1" cardioid condenser microphone has become an industry standard; delivering the warmth, extended dynamic range, clarity and high SPL capability typically only featured on some of the world’s most expensive microphones.
With a self-noise level of only 5dBA it is widely recognised (along with the NT1) as one the world's quietest studio microphones. This low noise makes it an ideal for vocal microphone as well as perfect for recording guitars and percussion.
Packaged in the 'Complete Vocal Recording Solution', the NT1-A includes everything you need to get a truly professional vocal recording and is ideal for home studio recording.
A studio grade pop shield and shock mount is included, along with a premium 20' microphone cable, dust cover, and an instructional DVD packed with recording tips.
The RØDE NT1-A large diaphragm 1" cardioid condenser microphone is designed and made in Australia, and covered by RØDE Microphones' industry leading 10 year warranty.
Specifications
| Acoustic Principle | Pressure Gradient |
| Active Electronics | JFET impedance converter with bipolar output buffer |
| Capsule | 1.00" |
| Polar Pattern | |
| Address Type | Side |
| Frequency Range | 20Hz - 20kHz |
| Output Impedance | 100Ω |
| Maximum SPL | 137dB SPL (@ 1kHz, 1% THD into 1KΩ load) |
| Maximum Output Level | 13.7mV |
| Sensitivity | -31.9dB re 1 Volt/Pascal (25.00mV @ 94 dB SPL) +/- 2 dB @ 1kHz |
| Equivalent Noise Level (A-weighted) | 5dB-A |
| Power Options |
+48V phantom power required from mixer or interface
|
| Weight | 326.00gm |
| Dimensions | 190.00mmH x 50.00mmW x 50.00mmD |
| Output | |
| Warranty | 1 year with free extension to 10 years following registration |
RØDE NT1000 Vocal Condenser Microphone
$ 329.00 - Sold Out
RØDE NT1000 Vocal Condenser Microphone
RØDE SKU: NT1000 | Helix SKU: RMNT1000
Overview
Versatile 1" cardioid condenser microphone
- HF2 1” capsule with gold-plated diaphragm
- Cardioid polar pattern
- True condenser (externally biased)
- Full frequency response
- Ultra low noise
- High strength welded and heat-treated mesh head
- Internal capsule shock mounting
- 10 year extended warranty when you register your microphone
With its ultra-low 6dBA self-noise and transformerless circuitry, the RØDE NT1000 exhibits exceptional performance when recording both vocals and instruments.
Voiced for versatility, it has been hailed by many as the ultimate microphone for grand piano and drum overheads. The NT1000 is also a fantastic vocal microphone.
The RØDE NT1000 microphone is designed and made in Australia, and covered by RØDE's industry leading 10 year warranty.
Specifications
|
Acoustic Principle |
Pressure Gradient |
| Active Electronics | Unity-gain closed-loop impedance converter; JFET input with bipolar buffering |
| Capsule | 1.00" |
| Polar Pattern | |
| Address Type | Side |
| Frequency Range | 20Hz - 20kHz |
| Output Impedance | 100Ω |
| Maximum SPL | 140dB SPL (@ 1kHz, 1% THD into 1KΩ load) |
| Maximum Output Level | 13.0mV |
| Sensitivity | -36.0dB re 1 Volt/Pascal (16.00mV @ 94 dB SPL) +/- 2 dB @ 1kHz |
| Equivalent Noise Level (A-weighted) | 6dB-A |
| Power Options |
|
| Weight | 682.00gm |
| Dimensions | 209.00mmH x 54.00mmW x 54.00mmD |
| Output | |
| Warranty | 1 year with free extension to 10 years following registration |
RØDE NT1Kit Cardioid Condenser Microphone w/SRM Combination Shock Mount & Dust Cover
$ 269.00 - Sold Out
RØDE NT1 Kit Cardioid Condenser Microphone with Shock Mount & Dust Cover.
RØDE SKU: NT1 Kit | Helix SKU: RMNT1Kit
Overview
The NT1 is a revolutionary new 1" diaphragm condenser microphone from RØDE.
Although the body of the new NT1 closely resembles the NT1-A, the microphone has been completely redesigned from the ground up, with the only shared component being the mesh grille.
RØDE’s design engineers approached the NT1 as a marriage of innovation and tradition, starting with the capsule which is a completely new design. Codenamed the HF6, it is the perfect example of RØDE’s fusion of artistic design approaches and cutting-edge manufacturing techniques, and features a sound signature reminiscent of the famous microphones of old while at the same time exhibiting extremely low noise.
It has been developed with a focus on detailed midrange response, coupled with silky smooth high frequencies, and warm, round, bass reproduction to make the NT1 an absolute standout in its class.
Specifications
| Operating Principle | Pressure Gradient |
| Transducer | Condenser |
| Diaphragm | 1" (25.40 mm) |
| Polar Pattern | Cardioid |
| Frequency Range | 20 Hz to 20 kHz |
| Equivalent Noise Level | 4 dB A-Weighted |
| Maximum SPL | 132 dB SPL 1% |
| Impedance | 100 ohms |
| Sensitivity | -29 dB, re: 1 V/Pa |
| Power Requirements | 24 V, 48 V |
| Output Connectors | 3-Pin XLR |
| Length | 7.36" (187 mm) |
| Diameter | 1.97" (50 mm) |
| Weight | 0.97 lb (440 g) |
Packaging Info
Package Weight 3.9 lb
Box Dimensions (LxWxH) 15.2 x 10.7 x 5.4"
