ProMaster XC-M 522 Column Tilt Adapter
$ 29.95
ProMaster XC-M 522 Column Tilt Adapter
ProMaster SKU: 4021 | Helix SKU: PR40215
Overview
The PROMASTER 4021 Column Tilt Adapter expands the capability of your XC-M 522 aluminum or XC-M 522C carbon fiber tripod by giving its center column the freedom to tilt 180° (90° up & 90° down). This adapter essentially converts your XC-M's center column into a multi-position, adjustable boom.
Just unscrew the weight hook from the center column, loosen the center column twist lock and slide it out of the tripod. Replace it with the 4021 Column Tilt Adapter, tighten the twist lock, and open the flip lock on the Column Tilt Adapter. Insert the center column and close the flip lock. This conversion can easily be done in less than 30 seconds. That's all there is too it!
Once your XC-M 522 has been converted you can reinstall the weight hook to the bottom of the adapter and add weight for more stability. A second, retractable weight hook is included with this adapter which you can use at the end of the boom (end of the center column) to counterweight your camera.
To operate the boom, loosen the main knob on the 4021 Adapter while holding your camera and then tilt the assembly into whatever position you like before tightening the knob. To rotate the boom, loosen the twist lock on the yoke of the tripod and spin the adapter. To extend or retract the boom use the twist lock on the column to adjust its upper stage.
This adapter has a number of teeth machined within its joint to give it an excellent amount of holding power in various tilt positions. Be sure to tighten its main knob before you release your camera to prevent it from falling.
The 4021 Column Tilt Adapter can be installed and used permanently on your XC-M 522, if you so choose, because it can achieve the same vertical position as the 'normal' center column when needed.
Truth be told, this is a wicked-cool accessory. It's great for macro work, extending your camera over a tabletop or a flowing creek. And it makes other tripods highly jealous.
Specifications
- Dimensions: 5 3/8" / 137 mm long. 22mm tube diameter.
- Weight: 4 3/8 oz / 124 g
* Dimensions and weight are for the adapter sans the weight hook
ProMaster XC-M 522 Extension & Macro Legs - Aluminum
$ 24.95
ProMaster XC-M 522 Extension & Macro Legs - Aluminum
ProMaster SKU: 3545 | Helix SKU: PR35457
Overview
The PROMASTER 3545 Aluminum Extension & Macro Legs work with XC-M 522 tripods. After removing all 3 of the XC-M 522's legs these extensions attach in their place. Now you have a choice. Either reattach the legs to these extensions and you get a very stable tripod with 6" more height, OR attach the 3 soft feet (included) to the extensions thereby converting your tripod into a lightweight, super-strong macro tripod.
The 3545 Extension & Macro Leg set adds amazing versatility to your XC-M 522 tripod.
Specifications
- Adds 6" / 152 mm of length to each XC-M 522 leg section
- Actual dimensions of each leg extension: 6 3/8" / 162 mm long x 22mm diameter
- Weight of each leg extension: 1 7/16 oz / 41 grams
- Weight of each foot: 3/8 oz / 11 grams
ProMaster XC-M 522 Ground Level Adapter - Aluminum
$ 12.95
ProMaster XC-M 522 Ground Level Adapter - Aluminum
ProMaster SKU: 3517 | Helix SKU: PR35174
Overview
The ProMaster 3517 Ground Level Adapter is a great accessory for getting an XC-M 522 tripod lower and closer to the ground for macro photography and a unique perspective.
Start by extending the upper stage of your XC-M's 2-stage center column. Unscrew the upper portion of the column (including the head) from the rest of the column. Now remove the weight hook and slide the lower part of the column completely out of the tripod. Replace it with the 3517 ground level adapter and insert the upper stage of the column into the 3517 adapter. Voila! In less than 30 seconds you have converted your XC-M 522 into a lowerider! You can now achieve a stable position as low as just 6" / 15.25 cm.
The Ground Level Adapter can also accept the XC-M's weight hook Just screw it into the bottom of the adapter and use it to add additional weight and stability to your XC-M 522.
FEATURES:
- Works with ProMaster XC-M 522 aluminum and XC-M 522 carbon fiber tripods
- Compatible with the XC-M 522 retractable weight hook
- Fast and easy to use
- Achieves a minimum working height of just 6" / 15.25 cm
Overview
- Dimensions: 3" / 76 mm long | 22 mm diameter tube
- Weight: 1 7/16 oz / 41 g
ProMaster XC-M 522 Ground Level Adapter - Carbon Fiber
$ 16.95
ProMaster XC-M 522 Ground Level Adapter - Carbon Fiber
ProMaster SKU: 3524 | Helix SKU: PR35242
Overview
The ProMaster 3524 Ground Level Adapter is a great accessory for getting an XC-M 522 tripod lower and closer to the ground for macro photography and a unique perspective.
Start by extending the upper stage of your XC-M's 2-stage center column. Unscrew the upper portion of the column (including the head) from the rest of the column. Now remove the weight hook and slide the lower part of the column completely out of the tripod. Replace it with the 3524 ground level adapter and insert the upper stage of the column into the 3524 adapter. Voila! In less than 30 seconds you have converted your XC-M 522 into a lowerider! You can now achieve a stable position as low as just 6" / 15.25 cm.
The Ground Level Adapter can also accept the XC-M's weight hook Just screw it into the bottom of the adapter and use it to add additional weight and stability to your XC-M 522.
FEATURES:
- Works with ProMaster XC-M 522 aluminum and XC-M 522 carbon fiber tripods
- Compatible with the XC-M 522 retractable weight hook
- Fast and easy to use
- Achieves a minimum working height of just 6" / 15.25 cm
Specifications
- Dimensions: 3" / 76 mm long | 22 mm diameter tube
- Weight: 1 3/16 oz / 34 g
ProMaster XC-M 522 Leg Warmers 3pc set - Black
$ 14.95
ProMaster XC-M 522 Leg Warmers 3pc set - Black
ProMaster SKU: 3594 | Helix SKU: PR35945
Overview
ProMaster's 3594 Leg Warmers are specifically designed for use with ProMaster XC-M 522 and XC-M 522C tripods. This kit of 3 warmers fits the 3 XC-M522 tripod legs perfectly. Simply wrap a leg warmer around the upper leg section of the tripod and zip it up. Now the leg is protected from scratches while covered in a soft sleeve. The warmers are much easier on your hands in cold weather too since they protect your skin from having direct contact with cold metal. And when you convert your XC-M tripod into its monopod mode, the warmer continues to perform as a soft, warm spot to hold on to.
Installing the leg warmers takes a bit of time and concentration since you have to line up the zipper while pulling the warmer tight around the leg. Be patient! Since it is an exact fitting item there is no slack in the fabric to ensure excellent performance once installed.
Specifications
- Actual length of each leg warmer: 5 1/8" / 130 mm
- Actual weight of each leg warmer: 13/32 oz / 11.5 g
ProMaster XC-M 522 Replacement Rubber Feet (set of 3)
$ 7.95
ProMaster XC-M 522 Replacement Rubber Feet (set of 3)
ProMaster SKU: 3503 | Helix SKU: PR35037
Overview
3503 is a replacement set of 3 standard feet for any XC-M 522 aluminum orcarbon fiber tripod. These are a great, inexpensive replacement set if you happen to lose or damage the standard feet on an XC-M 522 tripod.
The XC-M 522 standard feet are normally installed on the tripod from the factory. They are designed to be removable, thereby exposing a 3/8"-16 threaded port on the bottom of each XC-M 522 leg. The threaded ports can be used for connecting other accessories, like the popular All Terrain Feet (ProMaster product code 3510). If you need to replace any, or all 3 of the standard feet on a ProMaster XC-M 522 tripod this set is your solution.
* Please note, these feet do not work with the XC-M525 series tripods. If you need XC-M525 standard, replacement feet please refer to ProMaster product code 3720.
Specifications
Weight: 5/32 oz / 4.5 grams
ProMaster XC-M 522 Replacement Weight Hook
$ 5.95
ProMaster XC-M 522 Replacement Weight Hook
ProMaster SKU: 3706 | Helix SKU: PR37062
Overview
The 3706 is a replacement, retractable weight hook for any XC-M 522 aluminum or carbon fiber tripod. It connects to the bottom of the center column and allows you to attach additional weight to the tripod to improve its stability.
The 3706 is also a replacement hook for the 4021 XC-M 522 Tilting Column Adapter. With the Tilting Column Adapter installed you can add weight to the bottom of the adapter as well as to the bottom of the column. This improves the overall stability of the XC-M522 tripod while also counterbalancing your camera rig.
Finally, the 3706 also works with the 3517 XC-M 522 aluminum ground level adapter and the 3524 XC-M 522 carbon fiber ground level adapter.
Specifications
Weight: 9/32 oz / 8 grams
ProMaster XC-M 522C Extension & Macro Legs - Carbon Fiber
$ 34.95
ProMaster XC-M 522C Extension & Macro Legs - Carbon Fiber
ProMaster SKU: 3552 | Helix SKU: PR35525
Overview
The PROMASTER 3552 Carbon Fiber Extension & Macro Legs work with XC-M 522C tripods. After removing all 3 of the XC-M 522C's legs these extensions attach in their place. Now you have a choice. Either reattach the legs to these extensions and you get a very stable tripod with 6" more height, OR attach the 3 soft feet (included) to the extensions thereby converting your tripod into a lightweight, super-strong macro tripod.
The 3552 Extension & Macro Leg set adds amazing versatility to your XC-M 522C tripod.
Specifications
- Adds 6" / 152 mm of length to each XC-M 522C leg section
- Actual dimensions of each leg extension: 6 3/8" / 162 mm long x 22mm diameter
- Weight of each leg extension: 1 1/32 oz / 29 grams
- Weight of each foot: 3/8 oz / 11 grams
ProMaster XC-M 522K Professional Tripod Kit with Head - Black
$ 159.95
ProMaster XC-M 522K Professional Tripod Kit with Head - Black
ProMaster SKU: 3405 | Helix SKU: PR34054
Overview
The PROMASTER XC-M 522 tripod's 5-section, transverse legs fold 180° making the entire unit just over 12" long for storage and travel. Yet, fully extended it reaches a comfortable working height. Each leg's angle and length are independently adjustable, allowing the XC-M 522 to properly support your camera on uneven ground. Its dual-action ball head is strong, precise, and lightweight with an independent pan control. It has an integrated memory lock for repeatable tension control and uses ProMaster's dovetail quick release system for a fast camera connection.
The XC-M 522 is more than just a tripod, it's part of an expansive modular system.
FEATURES:
- Built-in monopod
- Transverse 180° folding legs
- Dual-action ball head with tension memory lock
- Independently adjustable leg angles
- 2-Stage, reversible center column
- Bubble levels on tripod and ball head
- Retractable weight hook
- ProMaster dovetail Q/R system (arca-swiss compatible)
- Soft, comfortable grips on touch points
- Modular design is expandable & customizable
Specifications
KIT SPECIFICATIONS
-
Maximum Working Height: 53 1/8" / 135 cm
-
Maximum Height with Column Down: 41 3/8" / 105 cm
-
Minimum Working Height: 12 1/2" / 31.8 cm *Minimum working height can be improved to 6" / 15.25 cm by adding a 3517 XC-M 522 Ground Level Adapter (sold separately)
-
Folded Length: 12 3/16" / 31 cm
-
Maximum Load: 11 lbs / 5 kg
-
Weight: 2 lbs 8 1/2 oz / 1.15 kg
-
Cold Weather Performance: -4° F / -20° C
- 5-Section Aluminum Legs
* Kit specifications include tripod with head attached
BALL HEAD SPECIFICATIONS
-
Height: 3 1/4" / 8.3 cm
-
Base Diameter: 1 5/8" / 4.1 cm
-
Weight: 8 oz / 226 grams
TRIPOD LEG SPECIFICATIONS
-
Maximum Working Height: 49 7/8" / 126.7 cm
-
Maximum Height with Column Down: 38 1/8" / 96.7 cm
-
Minimum Working Height: 9 1/4" / 23.5 cm
- Leg Angles: 20° / 50° / 80° / 180°
- Platform Diameter: 1 9/16" / 4 cm
-
Folded Length: 12 3/16" / 31 cm
-
Weight: 2 lbs 1/2 oz / .92 kg
CA Residents: Prop 65 WARNING(S)
ProMaster XC-M 522K Professional Tripod Kit with Head - Blue
$ 159.95
ProMaster XC-M 522K Professional Tripod Kit with Head - Blue
ProMaster SKU: 4070 | Helix SKU: PR40703
Overview
The PROMASTER XC-M 522 tripod's 5-section, transverse legs fold 180° making the entire unit just over 12" long for storage and travel. Yet, fully extended it reaches a comfortable working height. Each leg's angle and length are independently adjustable, allowing the XC-M 522 to properly support your camera on uneven ground. Its dual-action ball head is strong, precise, and lightweight with an independent pan control. It has an integrated memory lock for repeatable tension control and uses ProMaster's dovetail quick release system for a fast camera connection.
The XC-M 522 is more than just a tripod, it's part of an expansive modular system.
FEATURES:
- Built-in monopod
- Transverse 180° folding legs
- Dual-action ball head with tension memory lock
- Independently adjustable leg angles
- 2-Stage, reversible center column
- Bubble levels on tripod and ball head
- Retractable weight hook
- ProMaster dovetail Q/R system (arca-swiss compatible)
- Soft, comfortable grips on touch points
- Modular design is expandable & customizable
Specifications
KIT SPECIFICATIONS
-
Maximum Working Height: 53 1/8" / 135 cm
-
Maximum Height with Column Down: 41 3/8" / 105 cm
-
Minimum Working Height: 12 1/2" / 31.8 cm *Minimum working height can be improved to 6" / 15.25 cm by adding a 3517 XC-M 522 Ground Level Adapter (sold separately)
-
Folded Length: 12 3/16" / 31 cm
-
Maximum Load: 11 lbs / 5 kg
-
Weight: 2 lbs 8 1/2 oz / 1.15 kg
-
Cold Weather Performance: -4° F / -20° C
- 5-Section Aluminum Legs
* Kit specifications include tripod with head attached
BALL HEAD SPECIFICATIONS
-
Height: 3 1/4" / 8.3 cm
-
Base Diameter: 1 5/8" / 4.1 cm
-
Weight: 8 oz / 226 grams
TRIPOD LEG SPECIFICATIONS
-
Maximum Working Height: 49 7/8" / 126.7 cm
-
Maximum Height with Column Down: 38 1/8" / 96.7 cm
-
Minimum Working Height: 9 1/4" / 23.5 cm
- Leg Angles: 20° / 50° / 80° / 180°
- Platform Diameter: 1 9/16" / 4 cm
-
Folded Length: 12 3/16" / 31 cm
-
Weight: 2 lbs 1/2 oz / .92 kg
ProMaster XC-M 522K Professional Tripod Kit with Head - Red
$ 159.95
ProMaster XC-M 522K Professional Tripod Kit with Head - Red
ProMaster SKU: 3426 | Helix SKU: PR34269
Overview
The PROMASTER XC-M 522 tripod's 5-section, transverse legs fold 180° making the entire unit just over 12" long for storage and travel. Yet, fully extended it reaches a comfortable working height. Each leg's angle and length are independently adjustable, allowing the XC-M 522 to properly support your camera on uneven ground. Its dual-action ball head is strong, precise, and lightweight with an independent pan control. It has an integrated memory lock for repeatable tension control and uses ProMaster's dovetail quick release system for a fast camera connection.
The XC-M 522 is more than just a tripod, it's part of an expansive modular system.
FEATURES:
- Built-in monopod
- Transverse 180° folding legs
- Dual-action ball head with tension memory lock
- Independently adjustable leg angles
- 2-Stage, reversible center column
- Bubble levels on tripod and ball head
- Retractable weight hook
- ProMaster dovetail Q/R system (arca-swiss compatible)
- Soft, comfortable grips on touch points
- Modular design is expandable & customizable
Specifications
KIT SPECIFICATIONS
-
Maximum Working Height: 53 1/8" / 135 cm
-
Maximum Height with Column Down: 41 3/8" / 105 cm
-
Minimum Working Height: 12 1/2" / 31.8 cm *Minimum working height can be improved to 6" / 15.25 cm by adding a 3517 XC-M 522 Ground Level Adapter (sold separately)
-
Folded Length: 12 3/16" / 31 cm
-
Maximum Load: 11 lbs / 5 kg
-
Weight: 2 lbs 8 1/2 oz / 1.15 kg
-
Cold Weather Performance: -4° F / -20° C
- 5-Section Aluminum Legs
* Kit specifications include tripod with head attached
BALL HEAD SPECIFICATIONS
-
Height: 3 1/4" / 8.3 cm
-
Base Diameter: 1 5/8" / 4.1 cm
-
Weight: 8 oz / 226 grams
TRIPOD LEG SPECIFICATIONS
-
Maximum Working Height: 49 7/8" / 126.7 cm
-
Maximum Height with Column Down: 38 1/8" / 96.7 cm
-
Minimum Working Height: 9 1/4" / 23.5 cm
- Leg Angles: 20° / 50° / 80° / 180°
- Platform Diameter: 1 9/16" / 4 cm
-
Folded Length: 12 3/16" / 31 cm
-
Weight: 2 lbs 1/2 oz / .92 kg
CA Residents: Prop 65 WARNING(S)
ProMaster XC-M 525 Column Tilt Adapter
$ 34.95
ProMaster XC-M 525 Column Tilt Adapter
ProMaster SKU: 4028 | Helix SKU: PR40284
Overview
The PROMASTER 4028 Column Tilt Adapter expands the capability of your XC-M 525 aluminum or XC-M 525C carbon fiber tripod by giving its center column the freedom to tilt 180° (90° up & 90° down). This adapter essentially converts your XC-M's center column into a multi-position, adjustable boom.
Just unscrew the weight hook from the center column, loosen the center column twist lock and slide it out of the tripod. Replace it with the 4028 Column Tilt Adapter, tighten the twist lock, and open the flip lock on the Column Tilt Adapter. Insert the center column and close the flip lock. This conversion can easily be done in less than 30 seconds. That's all there is too it!
Once your XC-M 525 has been converted you can reinstall the weight hook to the bottom of the adapter and add weight for more stability. A second, retractable weight hook is included with this adapter which you can use at the end of the boom (end of the center column) to counterweight your camera.
To operate the boom, loosen the main knob on the 4028 Adapter while holding your camera and then tilt the assembly into whatever position you like before tightening the knob. To rotate the boom, loosen the twist lock on the yoke of the tripod and spin the adapter. To extend or retract the boom use the twist lock on the column to adjust its upper stage.
This adapter has a number of teeth machined within its joint to give it an excellent amount of holding power in various tilt positions. Be sure to tighten its main knob before you release your camera to prevent it from falling.
The 4028 Column Tilt Adapter can be installed and used permanently on your XC-M 525, if you so choose, because it can achieve the same vertical position as the 'normal' center column when needed.
Truth be told, this is a wicked-cool accessory. It's great for macro work, extending your camera over a tabletop or a flowing creek. And it makes other tripods highly jealous.
Specifications
- Dimensions: 5 3/4" / 146 mm long. 25mm tube diameter.
- Weight: 4 5/8 oz / 131 g
* Dimensions and weight are for the adapter sans the weight hook
ProMaster XC-M 525 Extension & Macro Legs - Aluminum
$ 29.95
ProMaster XC-M 525 Extension & Macro Legs - Aluminum
ProMaster SKU: 3559 | Helix SKU: PR35594
Overview
The PROMASTER 3559 Aluminum Extension & Macro Legs work with XC-M 525 tripods. After removing all 3 of the XC-M 525's legs these extensions attach in their place. Now you have a choice. Either reattach the legs to these extensions and you get a very stable tripod with nearly 8" more height, OR attach the 3 soft feet (included) to the extensions thereby converting your tripod into a lightweight, super-strong macro tripod.
The 3559 Extension & Macro Leg set adds amazing versatility to your XC-M 525 tripod.
Specifications
- Adds 7 7/8" / 200 mm of length to each XC-M 525 leg section
- Actual dimensions of each leg extension: 8 3/8" / 213 mm long x 25mm diameter
- Weight of each leg extension: 1 15/16 oz / 55 grams
- Weight of each foot: 9/16 oz / 16 grams
ProMaster XC-M 525 Ground Level Adapter - Aluminum
$ 15.95
ProMaster XC-M 525 Ground Level Adapter - Aluminum
ProMaster SKU: 3531 | Helix SKU: PR35310
Overview
The ProMaster 3531 Ground Level Adapter is a great accessory for getting an XC-M 525 tripod lower and closer to the ground for macro photography and a unique perspective.
Start by extending the upper stage of your XC-M's 2-stage center column. Unscrew the upper portion of the column (including the head) from the rest of the column. Now remove the weight hook and slide the lower part of the column completely out of the tripod. Replace it with the 3531 ground level adapter and insert the upper stage of the column into the 3531 adapter. Voila! In less than 30 seconds you have converted your XC-M 525 into a lowerider! You can now achieve a stable position as low as just 6 1/4" / 15.88 cm.
The Ground Level Adapter can also accept the XC-M's weight hook Just screw it into the bottom of the adapter and use it to add additional weight and stability to your XC-M 525.
FEATURES:
- Works with ProMaster XC-M 525 aluminum and XC-M 525 carbon fiber tripods
- Compatible with the XC-M 525 retractable weight hook
- Fast and easy to use
- Achieves a minimum working height of just 6 1/4" / 15.88 cm
Specifications
- Dimensions: 4 1/8" / 105 mm long | 25 mm diameter tube
- Weight: 1 13/16 oz / 51 g
ProMaster XC-M 525 Ground Level Adapter - Carbon Fiber
$ 19.95 - Sold Out
ProMaster XC-M 525 Ground Level Adapter - Carbon Fiber
ProMaster SKU: 3538 | Helix SKU: PR35389
Overview
The ProMaster 3538 Ground Level Adapter is a great accessory for getting an XC-M 525 tripod lower and closer to the ground for macro photography and a unique perspective.
Start by extending the upper stage of your XC-M's 2-stage center column. Unscrew the upper portion of the column (including the head) from the rest of the column. Now remove the weight hook and slide the lower part of the column completely out of the tripod. Replace it with the 3538 ground level adapter and insert the upper stage of the column into the 3538 adapter. Voila! In less than 30 seconds you have converted your XC-M 525 into a lowerider! You can now achieve a stable position as low as just 6 1/4" / 15.88 cm.
The Ground Level Adapter can also accept the XC-M's weight hook Just screw it into the bottom of the adapter and use it to add additional weight and stability to your XC-M 525.
FEATURES:
- Works with ProMaster XC-M 525 aluminum and XC-M 525 carbon fiber tripods
- Compatible with the XC-M 525 retractable weight hook
- Fast and easy to use
- Achieves a minimum working height of just 6 1/4" / 15.88 cm
Specifications
- Dimensions: 4 1/8" / 105 mm long | 25 mm diameter tube
- Weight: 1 9/16 oz / 44 g
ProMaster XC-M 525 Leg Warmers 3pc set - Black
$ 15.95
ProMaster XC-M 525 Leg Warmers 3pc set - Black
ProMaster SKU: 3601 | Helix SKU: PR36010
Overview
ProMaster's 3601 Leg Warmers are specifically designed for use with ProMaster XC-M 525 and XC-M 525C tripods. This kit of 3 warmers fits the 3 XC-M525 tripod legs perfectly. Simply wrap a leg warmer around the upper leg section of the tripod and zip it up. Now the leg is protected from scratches while covered in a soft sleeve. The warmers are much easier on your hands in cold weather too since they protect your skin from having direct contact with cold metal. And when you convert your XC-M tripod into its monopod mode, the warmer continues to perform as a soft, warm spot to hold on to.
Installing the leg warmers takes a bit of time and concentration since you have to line up the zipper while pulling the warmer tight around the leg. Be patient! Since it is an exact fitting item there is no slack in the fabric to ensure excellent performance once installed.
Specifications
- Actual length of each leg warmer: 8" / 203 mm
- Actual weight of each leg warmer: 5/8 oz / 18 g
ProMaster XC-M 525 Replacement Rubber Feet (set of 3)
$ 7.95
ProMaster XC-M 525 Replacement Rubber Feet (set of 3)
ProMaster SKU: 3720 | Helix SKU: PR37208
Overview
3720 is a replacement set of 3 standard feet for any XC-M 525 aluminum or carbon fiber tripod. These are a great, inexpensive replacement set if you happen to lose or damage the standard feet on an XC-M 525 tripod.
The XC-M 525 standard feet are normally installed on the tripod from the factory. They are designed to be removable, thereby exposing a 3/8"-16 threaded port on the bottom of each XC-M 525 leg. The threaded ports can be used for connecting other accessories, like the popular All Terrain Feet (ProMaster product code 3510). If you need to replace any, or all 3 of the standard feet on a ProMaster XC-M 525 tripod this set is your solution.
* Please note, these feet do not work with the XC-M522 series tripods. If you need XC-M522 standard, replacement feet please refer to ProMaster product code 3503.
Specifications
Weight: 3/16 oz / 5.4 grams - per foot
ProMaster XC-M 525 Replacement Weight Hook
$ 5.95
ProMaster XC-M 525 Replacement Weight Hook
ProMaster SKU: 3713 | Helix SKU: PR37130
Overview
The 3713 is a replacement, retractable weight hook for any XC-M 525 aluminum or carbon fiber tripod. It connects to the bottom of the center column and allows you to attach additional weight to the tripod to improve its stability.
The 3713 is also a replacement hook for the 4028 XC-M 525 Tilting Column Adapter. With the Tilting Column Adapter installed you can add weight to the bottom of the adapter as well as to the bottom of the column. This improves the overall stability of the XC-M525 tripod while also counterbalancing your camera rig.
Finally, the 3713 also works with the 3531 XC-M 525 aluminum ground level adapter and the 3538 XC-M 525 carbon fiber ground level adapter.
Specifications
Weight: 9/16 oz / 16 grams
ProMaster XC-M 525C Extension & Macro Legs - Carbon Fiber
$ 39.95
ProMaster XC-M 525C Extension & Macro Legs - Carbon Fiber
ProMaster SKU: 3566 | Helix SKU: PR35662
Overview
The PROMASTER 3566 Carbon Fiber Extension & Macro Legs work with XC-M 525C tripods. After removing all 3 of the XC-M 525C's legs these extensions attach in their place. Now you have a choice. Either reattach the legs to these extensions and you get a very stable tripod with nearly 8" more height, OR attach the 3 soft feet (included) to the extensions thereby converting your tripod into a lightweight, super-strong macro tripod.
The 3566 Extension & Macro Leg set adds amazing versatility to your XC-M 525C tripod.
Specifications
- Adds 7 7/8" / 200 mm of length to each XC-M 525C leg section
- Actual dimensions of each leg extension: 8 3/8" / 213 mm long x 25mm diameter
- Weight of each leg extension: 1 1/2 oz / 43 grams
- Weight of each foot: 9/16 oz / 16 grams
ProMaster XC-M 525CK Professional Carbon Fiber Tripod Kit with Head - Black
$ 269.95
ProMaster XC-M 525CK Professional Carbon Fiber Tripod Kit with Head - Black
ProMaster SKU: 3482 | Helix SKU: PR34825
Overview
The PROMASTER XC-M 525C tripod's 5-section, transverse legs fold 180° making the entire unit just over 15" long for storage and travel. Yet, fully extended it reaches an incredible working height of nearly 6'! Each leg's angle and length are independently adjustable, allowing the XC-M 525C to properly support your camera on uneven ground. Its dual-action ball head is strong, precise, and lightweight with an independent pan control. It has an integrated memory lock for repeatable tension control and uses ProMaster's dovetail quick release system for a fast camera connection.
The XC-M 525C is more than just a tripod, it's part of an expansive modular system.
FEATURES:
- Built-in monopod
- Transverse 180° folding legs
- Dual-action ball head with tension memory lock
- Independently adjustable leg angles
- 2-Stage, reversible center column
- Bubble levels on tripod and ball head
- Retractable weight hook
- ProMaster dovetail Q/R system (arca-swiss compatible)
- Soft, comfortable grips on touch points
- Modular design is expandable & customizable
Specifications
KIT SPECIFICATIONS
-
Maximum Working Height: 70 3/8" / 178.8 cm
-
Maximum Height with Column Down: 54 1/4" / 137.8 cm
-
Minimum Working Height: 15 1/8" / 38.4 cm *Minimum working height can be improved to 6 1/4" / 15.88 cm by adding a 3538 XC-M 525 Ground Level Adapter (sold separately)
-
Folded Length: 15" / 38.1 cm
-
Maximum Load: 17 lbs 10 oz / 8 kg
-
Weight: 2 lbs 13 5/16 oz / 1.29 kg
-
Cold Weather Performance: -4° F / -20° C
- 5-Section Carbon Fiber Legs
* Kit specifications include tripod with head attached
BALL HEAD SPECIFICATIONS
-
Height: 3 1/4" / 8.3 cm
-
Base Diameter: 1 13/16" / 4.6 cm
-
Weight: 8 5/8 oz / 245 grams
TRIPOD LEG SPECIFICATIONS
-
Maximum Working Height: 67 1/8" / 170.5 cm
-
Maximum Height with Column Down: 51" / 129.5 cm
-
Minimum Working Height: 11 7/8" / 30.1 cm
- Leg Angles: 20° / 50° / 80° / 180°
- Platform Diameter: 1 9/16" / 4 cm
-
Folded Length: 15" / 38.1 cm
-
Weight: 2 lbs 4 11/16 oz / 1.04 kg
CA Residents: Prop 65 WARNING(S)
ProMaster XC-M 525K Professional Tripod Kit with Head - Black
$ 189.95
ProMaster XC-M 525K Professional Tripod Kit with Head - Black
ProMaster SKU: 3447 | Helix SKU: PR34474
Overview
The PROMASTER XC-M 525 tripod's 5-section, transverse legs fold 180° making the entire unit just over 15" long for storage and travel. Yet, fully extended it reaches an incredible working height of nearly 6'! Each leg's angle and length are independently adjustable, allowing the XC-M 525 to properly support your camera on uneven ground. Its dual-action ball head is strong, precise, and lightweight with an independent pan control. It has an integrated memory lock for repeatable tension control and uses ProMaster's dovetail quick release system for a fast camera connection.
The XC-M 525 is more than just a tripod, it's part of an expansive modular system.
FEATURES:
- Built-in monopod
- Transverse 180° folding legs
- Dual-action ball head with tension memory lock
- Independently adjustable leg angles
- 2-Stage, reversible center column
- Bubble levels on tripod and ball head
- Retractable weight hook
- ProMaster dovetail Q/R system (arca-swiss compatible)
- Soft, comfortable grips on touch points
- Modular design is expandable & customizable
Specifications
KIT SPECIFICATIONS
-
Maximum Working Height: 70 3/8" / 178.8 cm
-
Maximum Height with Column Down: 54 1/4" / 137.8 cm
-
Minimum Working Height: 15 1/8" / 38.4 cm *Minimum working height can be improved to 6 1/4" / 15.88 cm by adding a 3531 XC-M 525 Ground Level Adapter (sold separately)
-
Folded Length: 15" / 38.1 cm
-
Maximum Load: 17 lbs 10 oz / 8 kg
-
Weight: 3 lbs 4 7/8 oz / 1.5 kg
-
Cold Weather Performance: -4° F / -20° C
- 5-Section Aluminum Legs
* Kit specifications include tripod with head attached
BALL HEAD SPECIFICATIONS
-
Height: 3 1/4" / 8.3 cm
-
Base Diameter: 1 13/16" / 4.6 cm
-
Weight: 8 5/8 oz / 245 grams
TRIPOD LEG SPECIFICATIONS
-
Maximum Working Height: 67 1/8" / 170.5 cm
-
Maximum Height with Column Down: 51" / 129.5 cm
-
Minimum Working Height: 11 7/8" / 30.1 cm
- Leg Angles: 20° / 50° / 80° / 180°
- Platform Diameter: 1 9/16" / 4 cm
-
Folded Length: 15" / 38.1 cm
-
Weight: 2 lbs 12 1/4 oz / 1.25 kg
CA Residents: Prop 65 WARNING(S)
ProMaster XC-M 525K Professional Tripod Kit with Head - Blue
$ 189.95
ProMaster XC-M 525K Professional Tripod Kit with Head - Blue
ProMaster SKU: 4077 | Helix SKU: PR40772
Overview
The PROMASTER XC-M 525 tripod's 5-section, transverse legs fold 180° making the entire unit just over 15" long for storage and travel. Yet, fully extended it reaches an incredible working height of nearly 6'! Each leg's angle and length are independently adjustable, allowing the XC-M 525 to properly support your camera on uneven ground. Its dual-action ball head is strong, precise, and lightweight with an independent pan control. It has an integrated memory lock for repeatable tension control and uses ProMaster's dovetail quick release system for a fast camera connection.
The XC-M 525 is more than just a tripod, it's part of an expansive modular system.
FEATURES:
- Built-in monopod
- Transverse 180° folding legs
- Dual-action ball head with tension memory lock
- Independently adjustable leg angles
- 2-Stage, reversible center column
- Bubble levels on tripod and ball head
- Retractable weight hook
- ProMaster dovetail Q/R system (arca-swiss compatible)
- Soft, comfortable grips on touch points
- Modular design is expandable & customizable
Specifications
KIT SPECIFICATIONS
-
Maximum Working Height: 70 3/8" / 178.8 cm
-
Maximum Height with Column Down: 54 1/4" / 137.8 cm
-
Minimum Working Height: 15 1/8" / 38.4 cm *Minimum working height can be improved to 6 1/4" / 15.88 cm by adding a 3531 XC-M 525 Ground Level Adapter (sold separately)
-
Folded Length: 15" / 38.1 cm
-
Maximum Load: 17 lbs 10 oz / 8 kg
-
Weight: 3 lbs 4 7/8 oz / 1.5 kg
-
Cold Weather Performance: -4° F / -20° C
- 5-Section Aluminum Legs
* Kit specifications include tripod with head attached
BALL HEAD SPECIFICATIONS
-
Height: 3 1/4" / 8.3 cm
-
Base Diameter: 1 13/16" / 4.6 cm
-
Weight: 8 5/8 oz / 245 grams
TRIPOD LEG SPECIFICATIONS
-
Maximum Working Height: 67 1/8" / 170.5 cm
-
Maximum Height with Column Down: 51" / 129.5 cm
-
Minimum Working Height: 11 7/8" / 30.1 cm
- Leg Angles: 20° / 50° / 80° / 180°
- Platform Diameter: 1 9/16" / 4 cm
-
Folded Length: 15" / 38.1 cm
-
Weight: 2 lbs 12 1/4 oz / 1.25 kg
ProMaster XC-M 525K Professional Tripod Kit with Head - Red
$ 189.95
ProMaster XC-M 525K Professional Tripod Kit with Head - Red
ProMaster SKU: 3468 | Helix SKU: PR34689
Overview
The PROMASTER XC-M 525 tripod's 5-section, transverse legs fold 180° making the entire unit just over 15" long for storage and travel. Yet, fully extended it reaches an incredible working height of nearly 6'! Each leg's angle and length are independently adjustable, allowing the XC-M 525 to properly support your camera on uneven ground. Its dual-action ball head is strong, precise, and lightweight with an independent pan control. It has an integrated memory lock for repeatable tension control and uses ProMaster's dovetail quick release system for a fast camera connection.
The XC-M 525 is more than just a tripod, it's part of an expansive modular system.
FEATURES:
- Built-in monopod
- Transverse 180° folding legs
- Dual-action ball head with tension memory lock
- Independently adjustable leg angles
- 2-Stage, reversible center column
- Bubble levels on tripod and ball head
- Retractable weight hook
- ProMaster dovetail Q/R system (arca-swiss compatible)
- Soft, comfortable grips on touch points
- Modular design is expandable & customizable
Specifications
KIT SPECIFICATIONS
-
Maximum Working Height: 70 3/8" / 178.8 cm
-
Maximum Height with Column Down: 54 1/4" / 137.8 cm
-
Minimum Working Height: 15 1/8" / 38.4 cm *Minimum working height can be improved to 6 1/4" / 15.88 cm by adding a 3531 XC-M 525 Ground Level Adapter (sold separately)
-
Folded Length: 15" / 38.1 cm
-
Maximum Load: 17 lbs 10 oz / 8 kg
-
Weight: 3 lbs 4 7/8 oz / 1.5 kg
-
Cold Weather Performance: -4° F / -20° C
- 5-Section Aluminum Legs
* Kit specifications include tripod with head attached
BALL HEAD SPECIFICATIONS
-
Height: 3 1/4" / 8.3 cm
-
Base Diameter: 1 13/16" / 4.6 cm
-
Weight: 8 5/8 oz / 245 grams
TRIPOD LEG SPECIFICATIONS
-
Maximum Working Height: 67 1/8" / 170.5 cm
-
Maximum Height with Column Down: 51" / 129.5 cm
-
Minimum Working Height: 11 7/8" / 30.1 cm
- Leg Angles: 20° / 50° / 80° / 180°
- Platform Diameter: 1 9/16" / 4 cm
-
Folded Length: 15" / 38.1 cm
-
Weight: 2 lbs 12 1/4 oz / 1.25 kg
CA Residents: Prop 65 WARNING(S)
ProMaster XC-M All Terrain Feet (set of 3)
$ 29.95
ProMaster XC-M All Terrain Feet (set of 3)
ProMaster SKU: 3510 | Helix SKU: PR35105
Overview
The PROMASTER 3510 ALL TERRAIN FEET are a serious upgrade for any XC-M tripod.
Once the standard feet are removed (simply pull them off the bottom of each XC-M leg while applying a little bit of wiggle action) you can install the stainless-steel spikes into the threaded port found at the bottom of each XC-M leg. An included wrench will help you to tighten the spikes in place. These spikes are great for solid footing on ice, dirt, grass, and more. But what if you find your XC-M's legs sinking into soft ground like sand or snow? Never fear! Just attach the sand/snow baskets directly to the spikes for excellent stability on soft ground.
Finally, 3 soft tips are included with this kit for use on delicate surfaces such as wood floors. The soft tips push onto the spikes and can be applied either with, or without the sand/snow baskets in installed.
This kit is truly one of the most versatile accessories for using your tripod on any kind of terrain. It is designed for ProMaster XC-M 522 and XC-M525 aluminum and carbon fiber tripods.
Specifications
- Weight of 1, fully assembled foot: 42 grams
- Weight of 1 spike only: 24 grams
- Weight of 1 sand / snow basket only: 8 grams
- Weight of 1 soft tip only: 10 grams
ProMaster XC-M Hipster & Strap
$ 29.95
ProMaster XC-M Hipster & Strap
ProMaster SKU: 3587 | Helix SKU: PR35877
Overview
The ProMaster Hipster and Strap works with all models of XC-M tripods. This unique system offers multiple ways of carrying a tripod. There are two parts to this system, the Hipster and the strap.
The Hipster is a holster which allows two of the tripod's legs to slide into it while one leg overlaps the front so the tripod can be removed lightning fast. The Hipster easily attaches to a belt or camera bag/backpack using its Velcro-loop attachment on its back side. The Hipster also has two metal D-rings which act as quick-connection points for the strap. Using the quick release metal buckles on the strap you can attach the Hipster and carry your tripod over your shoulder.
The shoulder strap has a soft shoulder pad for comfortable carrying. It also has a tool pouch built-in, which is a great way to carry spare wrenches for adjustments in the field. Since every XC-M includes a tool kit, the integrated pouch on this strap is a very convenient way of storing and carrying those tools.
But wait, there's more! Inside of the Hipster is a sewn-in pocket. When wearing the Hipster on your belt in front of your body, you can convert your XC-M into a monopod and place the foot of the monopod into this pocket for stability. This makes a great stabilizing rig, especially for videography.
ProMaster XC-M Shoulder Strap
$ 19.95
ProMaster XC-M Shoulder Strap
ProMaster SKU: 3580 | Helix SKU: PR35808
Overview
This shoulder strap works with all ProMaster XC-M tripods. It quickly attaches the the machined strap slot in the yoke of an XC-M tripod using a quick release buckle. The other side of the strap slides around the lower portion of the tripod's legs like a lasso.
The XC-M shoulder strap has a soft shoulder pad for comfortable carrying. It also has a tool pouch built-in, which is a great way to carry spare wrenches for adjustments in the field. Since every XC-M includes a tool kit the integrated pouch on this strap is a very convenient way of storing and carrying those tools.
Specifications
- Length: 45" / 114 cm - maximum overall length of strap, including buckle, when adjusted to its longest position.
ProMaster XC-MH26 Ball Head - Black
$ 79.95
ProMaster XC-MH26 Ball Head - Black
ProMaster SKU: 3489 | Helix SKU: PR34894
Overview
The PROMASTER XC-MH26 BALL HEAD is well featured, technical ball head with incredible strength in a compact and lightweight form factor. It is made of machined (not cast) high grade aluminum.
The XC-MH26's dual action design uses separate knobs to adjust the ball tension and the panning control. An etched, numbered scale is applied to the base of this head for precise panning movements. The tension control knob has an integrated memory lock dial which allows you to set a repeatable tension stop. Its quick release system uses a dovetail style plate (arca-type) with safety bolts. All knobs are covered in a soft yet grippy material that is comfortable and easy on your fingers, even in cold weather. Multiple bubble levels (1 bullseye and 2 line levels) are integrated so you can precisely level your camera in either a horizontal or vertical position. The included quick release plate has a strap slot which is compatible with a variety of straps and hand grips.
Specifications
INCLUDES:
- 1 XC-M26 Ball Head
- 1 3608 Quick Release Plate
SPECIFICATIONS:
-
Height: 3 1/4" / 8.3 cm
-
Base Diameter: 1 5/8" / 4.1 cm
-
Weight: 8 oz / 226 grams
- Maximum Load: 11 lbs / 5 kg
- Cold Weather Performance: -4° F / -20° C
CA Residents: Prop 65 WARNING(S)
ProMaster XC-MH30 Ball Head - Black
$ 89.95
ProMaster XC-MH30 Ball Head - Black
ProMaster SKU: 3496 | Helix SKU: PR34962
Overview
The PROMASTER XC-MH30 BALL HEAD is well featured, technical ball head with incredible strength in a compact and lightweight form factor. It is made of machined (not cast) high grade aluminum.
The XC-MH30's dual action design uses separate knobs to adjust the ball tension and the panning control. An etched, numbered scale is applied to the base of this head for precise panning movements. The tension control knob has an integrated memory lock dial which allows you to set a repeatable tension stop. Its quick release system uses a dovetail style plate (arca-type) with safety bolts. All knobs are covered in a soft yet grippy material that is comfortable and easy on your fingers, even in cold weather. Multiple bubble levels (1 bullseye and 2 line levels) are integrated so you can precisely level your camera in either a horizontal or vertical position. The included quick release plate has a strap slot which is compatible with a variety of straps and hand grips.
Specifications
INCLUDES:
- 1 XC-MH30 Ball head
- 1 3608 Quick Release Plate
SPECIFICATIONS:
-
Height: 3 1/4" / 8.3 cm
-
Base Diameter: 1 13/16" / 4.6 cm
-
Weight: 8 5/8 oz / 245 grams
- Maximum Load: 17 lbs 10 oz / 8 kg
- Cold Weather Performance: -4° F / -20° C
CA Residents: Prop 65 WARNING(S)
ProMaster XtraPower AA Battery Case
$ 4.95
ProMaster XtraPower AA Battery Case
ProMaster XtraPower AC Replacement Cord
$ 9.95
ProMaster XtraPower AC Replacement Cord
Promaster XtraPower PRO NiMH Batteries - AA 4-Pack
$ 8.78
Promaster XtraPower PRO NiMH Batteries - AA 4-Pack PROMASTER XtraPower PRO batteries are ultra high performance Ni-MH cells designed to give you the absolute best performance for digital cameras. They can be recharged up to 1000 times! Memory free operation means you can charge PROMASTER batteries anytime you like. When long lasting capacity is what you need, PROMASTER XtraPower PRO batteries are the perfect choice. XtraPower PRO batteries are always supplied in the maximum capacity currently available in the market. 4 high capacity NiMH AA batteries Battery storage case
ProMediaGear BBGv2 - Boomerang Flash Bracket for taller bodies or cameras w/ grip for Weddings and Portraits for Canon, Nikon, Sony, Pentax, Olympus
$ 349.95
ProMediaGear BBGv2 - Boomerang Flash Bracket for taller bodies or cameras w/ grip for Weddings and Portraits for Canon, Nikon, Sony, Pentax, Olympus
ProMediaGear SKU: BBGv2-PBX3 | Helix SKU: PMGBBGv2PBX3
Overview
Positioning the flash above the lens eliminates shadows and Red-Eye, greatly improving the lighting quality in your photographs. Improving images “in camera” will reduce post processing time, saving hours of potential retouching. It’s the perfect camera accessory for fast paced situations like weddings and events.
The BBGv2 has been designed and optimized for tall cameras, Canon 1Dx, Nikon D5 or similar, and also cameras utilizing the optional battery pack / grip, Canon BG-E20, Nikon MB-D18 or similar. The arc shaped flash arm mounting platform allows for unrestricted access to the vertical grip controls and does not block the battery compartments.
The Boomerang places the flash away from the hot shoe, allowing unrestricted access for a wireless controller / transmitter. The flash plate is capable of mounting wired and wireless speedlights, battery powered Flash Heads and so much more.
The Boomerang Flash Bracket is built around our Arca Compatible Camera Mounting Plate aka: Bracket Plate. The Flash Bracket comes complete with our Universal PBX3 Bracket Plate or you may select a custom anti-twist plate specifically for your camera model/type in the drop-down. The Flash Bracket attaches to our Bracket Plate with a thumbwheel, no tools required.
Additionally, accessories such as: L-brackets, Handles, Port Protectors and other Adapters may be attached to our Bracket Plate system without blocking the Arca Compatible Base. These accessories provide the ability to add other gear such as microphones, monitors and triggers with ease to better fit your shooting style. Look into related items below to see what works with the BBGv2.
The unit quickly folds down and can easily be stored in your gear bag when not in use.
It consists of 3 major assemblies
(1) Camera Mounting Plate (The Bracket Plate Universal or Custom)
(2) BBGv2 Boomerang Main Body Arc
(3) Flash Rotation Arm
- Quickly and Smoothly Rotates Flash Units 90º
- Perfect companion for flash heads. Works with any type of Speedlight or Portable Flash System
- Fits DSLRs and Mirrorless Cameras with Vertical Battery Grip
- Compact, modular, folding design
- Fold-Away Kickstand
- Allows for Easy Battery Access
- Manufactured from high strength T6061 Aircraft Grade aluminum and Titanium Alloys
- Professional grade rotation bearings require no lubrication
- Reduce or eliminate subject side shadows and red-eye
- Enhances subject lighting and reduces post processing time
- Lightweight weighs only 17.3 oz (491 grams)
- Made in U.S.A CNC precision machined construction
- 30-day money back guarantee with free ground shipping in the United States
ProMediaGear BH1 Professional Ball Head with Arca-Type Clamp
$ 499.95
ProMediaGear BH1 Professional Ball Head with Arca-Type Clamp
ProMediaGear SKU: BH1 | Helix SKU: PMGBH1
Overview
ProMediaGear Sputnik Ball Head
Ball Head is an essential item in any Professional Photographers Gear Bag.
ProMediaGear #BH1 ball head is not your average ball head. Made to Last, it's CNC precision crafted in the USA, from best alloys and stainless steel, it has all the features you need in a professional ball head.
The knob dominates and shapes the entire ball head, it's large and easy to feel and find from any angle. Designed for fast action adjustments, it allows for 90-degree tilting in any opposite direction, at any time in any direction, unlike typical ball heads that allow 90 degree tilts only in a predefined slot.
This Ball Head is suitable for Wide Angle to Super Telephoto lenses, Outdoor and Wildlife Photography, and can be used with any camera. Whether you are a Nikon, Canon or Sony shooter, it will improve the quality of your pictures and better your skills in the easiest way possible.
The clamp is laser engraved with millimeter scale for precise positioning of the camera.
Order with Confidence: We are certain that you will love our Ball Head as much as we do but if for any reason you are not completely satisfied, we will give you a full refund – no questions asked! And if something goes wrong, we offer you a 5-year warranty so you will have nothing to worry about!
Specifications
Specifications:
- H x W x L : 5.5 x 4.25 x 4.5 inches
- Base Diameter: 2.80 inches / 7.11 cm
- Load Capacity: 50 lbs - 23KG
- Weight: 2.03 lbs, 920grams
- Mount: 3/8-16 Female Threaded Adapter (Standard Tripod Thread)
- T6061 Aluminum Alloy
- Black Anodized Scratch Resistant Finish
- Arca-Swiss type Compatible Clamp
- Made in USA
- 5-Year Warranty
Item Includes
What's in the Box:
- #BH1 Ball Head
- #PBX3 Universal Bracket Plate (Arca Compatible)
- Allen Key Set
ProMediaGear Katana Junior Telephoto Lens Gimbal Head
$ 649.95
ProMediaGear Katana Junior Telephoto Lens Gimbal Head
ProMediaGear SKU: GKJR | Helix SKU: PMGGKJR
Overview
Features:- Smooth panning and tilt locking mechanism (separate from assembly mounts)
- Arca-Swiss compatible lens mount
- Hard anodized scratch resistant finish
- Sealed, Maintenance Free, Ball Bearings
- Lightweight aircraft quality aluminum
- CNC Precision machined parts
- 5-year warranty
- Rated below freezing (-40 Celsius) for smooth operation without motion freeze
- Made in USA
Specifications
Specifications:
- Length: 8.48 inches
- Width: 3.10 inches (including knob)
- Height: 9.75 inches
- Weight: 2.40 pounds
- Load Capacity: 50 lbs (22.68 KG)
- Mount Thread: 3/8-16
- Mounting Base: 2.36 inches
Item Includes
Items Included:
• Lens Plate (PX6) (FREE Promotional Item)
ProMediaGear TR343 34mm Series 51" Pro-Stix Carbon-Fiber Tripod with Top Plate
$ 1,059.95 - Sold Out
ProMediaGear TR343 34mm Series 51" Pro-Stix Carbon-Fiber Tripod with Top Plate
ProMediaGear SKU: TR343 | Helix SKU: PMGTR343
Overview
The Pro-Stix Carbon Fiber Series Tripods are designed and built for the professional videographer or photographer looking for the toughest and most rugged tripod. The tripods are rated to support loads up to 60 lbs. The apex features an interchangeable flat plate that can be removed and transitioned to various accessories such as our #TRB3475 75mm Leveling Bowl insert. The apex plate has a 3/8-16 standard mounting thread for Ball Heads, Video Heads, Gimbals, Sliders and much more.
The carbon fiber legs have 3 adjustable locking angle positions to accommodate any shooting situation, high to low. Each side of the apex features a 1/4-20 threaded adapter port to mount additional accessories. One of the adapter ports comes complete with a large and easy to read spirit level. Lastly, each tripod foot has a hardened stainless-steel spike integrated inside the tube. The entire line-up of ProMediaGear Pro-Stix Carbon Fiber Tripods are precision CNC machined in our factory located in Tinley Park, IL USA.
Specifications
Item Includes
Quantum Bantam Battery Power Module Xi f/ Minolta 3200i
$ 5.00
Quantum Bantam Battery Power Module Xi f/ Minolta 3200i
Quantum Bantam Battery Power Module XKE for Nikon SB24, SB25
$ 35.00
Quantum Bantam Battery Power Module XKE for Nikon SB24, SB25
Quantum QF80 Qflash UV/IR Wave Reflector
$ 87.95
Quantum QF80 Qflash UV/IR Wave Reflector
Quantum SKU: 862541 | Helix SKU: QU862541
Special Order Item
Overview
Quantum Instruments’ QF80 Qflash UV/IR Wave Reflector provides Ultraviolet (UV) and Infrared (IR) filtration capability for Quantum’s portable Qflash bracket-mounted flash units.
*Special Order Items Are Not Returnable.
Specifications
UPC: 807955011699
Remote Switch 60-T3 , 2'
$ 5.00
Electromagnetic cable release. Operates AF & metering separately from shutter release, also features Running Lock.
For the T70, T90, EOS 650, 620, 750, 850, 630, 1, RT, A2, A2e, 1N & 1N-RS Cameras 1V, 1V-HS & EOS 3 Cameras Require Adapters
Retrospective 20 -Black
$ 174.75
Created for the professional photographer that wants to blend in with the crowd and remain inconspicuous in any situation. This bag combines the look and feel of "old-school" camera bags with "new-school" features and technology for the digital imaging age. KEY FEATURES Minimalist outer appearance conceals expensive photo equipment Carries a gripped DSLR with zoom lens attached Taller size to fit a 70-200mm f/2.8 lens attached to camera Black (1100D 'polyspun' polyester exterior fabric), Pinestone (sand washed cotton canvas) and Blue State (sand washed cotton canvas) GEAR PROFILE 1 gripped DSLR with up to a 70-200mm f/2.8 lens attached, plus 1-3 additional lenses 1 gripped DLSR (body only) in front pocket and 2-4 lenses in main compartment, including a 70-200mm f/2.8 1 standard body attached to a 70-200mm f/2.8 alongside a 300mm f/2.8 lens unattached TECHNICAL SPECIFICATIONS Interior Dimensions: 12" W x 11.75" H x 6" D (30.5 x 29.8 x 15.2 cm)* *Bag softness and flexibility allows expansion to carry a pro size DSLR with lens attached, facing down Exterior Dimensions: 13" W x 12.5" H x 7" D (33 x 31.7 x 17.8 cm) Weight: 3.2 lbs (1.5 kg) MATERIALS Exterior: For superior water-resistance, all exterior fabric has a durable water-repellent (DWR) coating, plus the underside of the fabric has a polyurethane coating. It's also constructed with 1100D polyspun polyester, antique nickel-plated metal hardware, YKK® RC Fuse (abrasion resistant) zippers, nylon webbing, 3-ply bonded nylon thread. Interior: Removable closed cell foam inserts with reinforced PE board, 210D silver-toned nylon, polyurethane-backed Velex, 2x polyurethane-coated nylon 210T seam-sealed rain cover, 3-ply bonded nylon thread.
Rhino Arc II Charger
$ 30.00 - Sold Out
Rhino Arc II Charger
The Arc II Charger will charge your Arc II unit in 2 hours and comes with four interchangeable international plugs.
Features
- Ultra fast charging for Rhino Arc II
-
Interchangeable plugs
Specs
- 12V 48W International charger
In the box
- Arc II Charger
- US, UK, EU, AU plugs included
Rhino Basic Slider Bundle
$ 800.00
Rhino Basic Slider Bundle SKU253
Rhino SKU: SKU253 | Helix SKU: RHSKU253
Overview
This is the perfect bundle for minimalist filmmaker. No batteries or electronics to rely on. Just simple, smooth, cinematic filming.
Features
- Interia powered dampening
- Creates ultra smooth slider shots
-
No batteries to charge
Includes
- Rhino Slider Carbon 24"
- Rhino Flywheel
- 24" Carrying Case
Rhino Carbon 24" Rails
$ 250.00
Rhino Carbon 24" Rails
Rhino SKU: SKU209 | Helix SKU:RHSKU209
Overview
Interchangeable rails are the heart of the Rhino System. They allow you to completely change the weight, length, and load capacity of your slider setup without having to buy a completely new setup.
The Carbon 24” Rails are the most versatile of the four options. They are short, light, and super rigid making them great for most everyday shoots.
Weight: 1lb
Load Capacity: 15lbs
We updated the rails with our new Tripod Quick Mount System that lets you mount your slider to a tripod in less time and without having to awkwardly spin it around.
Features
- Quickly interchange your rails to transform your slider
- Ultra light
- Precision ground carbon fiber
- Includes the new Tripod Quick Mount System
Includes
- Carbon 24” Rails
Rhino Carbon 42" Rails
$ 450.00
Rhino Carbon 42" Rails
Interchangeable rails are the heart of the Rhino System. They allow you to completely change the weight, length, and load capacity of your slider setup without having to buy a completely new setup.
The Carbon 42” Rails are perfect for time-lapse shots and longer interview setups. Thanks to the new dual Tripod Quick Mount plates they are 5x more torsionally rigid than our previous 42” rails. This makes them much for versatile and less prone to twist when filming with heavy setups.
Weight: 1lb 12oz
Load Capacity: 10lbs
We updated the rails with our new Tripod Quick Mount System that lets you mount your slider to a tripod in less time and without having to awkwardly spin it around.
Features
- Quickly interchange your rails to transform your slider
- Ultra light and 5x more rigid than our previous version
- Precision ground carbon fiber
- Includes the new Tripod Quick Mount System
- Easy mounting to dual tripods
In the box
- Carbon 42” Rails
Rhino Carrying Case 24"
$ 100.00
Rhino Carrying Case 24"
Rhino SKU: SKU094 | Helix SKU: RHSKU094
Overview
PRODUCT DESCRIPTION:
The Slider Carrying Case is a padded soft shell case that is designed to carry your complete Rhino Slider setup when you’re filming locally. It allows you to store your Rhino Slider with Arc II, Focus, and Motor attached so you don’t have to take down your kit everytime you film at a new location. Setup is as simple as mounting to a tripod using the new Tripod Quick Mount System and powering your gear on.
Note: This version is slightly longer than the previous carrying case to allow for the longer motor to fit assembled.
Fits:
- Assembled Rhino Slider 24” or 42” (with Arc II, Focus, and Motor attached)
- Interchangeable Rails (on 42” version only)
Features
- Safely carry your entire Rhino Slider setup completely assembled
- Internal straps secure your slider
- Accessory pocket on the outside
- Padded shoulder strap
In the box
- Slider Carrying Case 24”
Rhino Carrying Case 42"
$ 150.00 - Sold Out
Rhino Slider EVO Carrying Case 42"
Rhino SKU: SKU095 | Helix SKU: RHSKU095
Overview
PRODUCT DESCRIPTION:
The Slider Carrying Case is a padded soft shell case that is designed to carry your complete Rhino Slider setup when you’re filming locally. It allows you to store your Rhino Slider with Arc II, Focus, and Motor attached so you don’t have to take down your kit everytime you film at a new location. Setup is as simple as mounting to a tripod using the new Tripod Quick Mount System and powering your gear on.
Note: This version is slightly longer than the previous carrying case to allow for the longer motor to fit assembled.
Fits
- Assembled Rhino Slider 24” or 42” (with Arc II, Focus, and Motor attached)
- Interchangeable Rails (on 42” version only)
Features
- Safely carry your entire Rhino Slider setup completely assembled
- Internal straps secure your slider
- Accessory pocket on the outside
- Padded shoulder strap
In the box
- Slider Carrying Case 42”
Rhino Essentials Slider Bundle
$ 2,350.00 - Sold Out
Rhino Essentials Slider Bundle
Rhino SKU: SKU252 | Helix SKU: RHSKU252
Overview
This bundle has everything you need to motorized your slider and start getting incredible 3-axis movement.
Make sure to add Rhino Focus to your bundle to keyframe your focus for even more dynamic shots.
Features
- Ultra light carbon fiber rails are easy to pack
- High Speed Motor lets you set-up moves faster
- Carry your gear completely set-up in the soft shell case
In the box
- Rhino Slider Carbon 24”
- Rhino Arc II
- Rhino Motor - High Speed
- Slider Carrying Case 24”
Rhino Everyday Backpack
$ 80.00 - Sold Out
Rhino Everyday Backpack
Rhino SKU: ROV005 | Helix SKU: RHROV005
Overview
The ROV Everyday Backpack is custom designed to fit your ROV Everyday Slider. It allows you to take ROV everywhere your camera does to capture beautiful cinematic slider shots.
Features
- Carry and protect your ROV Everyday Slider
- Durable nylon construction
- Side handle for easy carry
- Accessory pockets for your mobile lenses and gear
In the box
- Everyday backpack
